- 您現在的位置：買賣IC網 > PDF目錄373805 > ZNBG6001 (Zetex Semiconductor) MS3470L14-15S PDF資料下載
參數資料
| 型號： | ZNBG6001 |
| 廠商： | Zetex Semiconductor |
| 英文描述： | MS3470L14-15S |
| 中文描述： | 場效應管偏置控制器 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 406K |
| 代理商： | ZNBG6001 |
ZNBG4000 ZNBG4001
ZNBG6000 ZNBG6001
TYPICAL APPLICATION CIRCUIT
APPLICATIONS INFORMATION
The above is a partial application circuit for the ZNBG series showing all external components
required for appropriate biasing. The bias circuits are unconditionally stable over the full
temperature range with the associated FETs and gate and drain capacitors in circuit.
Capacitors C
and C
ensure that residual power supply and substrate generator noise is not
allowed to affect other external circuits which may be sensitive to RF interference. They also
serve to suppress any potential RF feedthrough between stages via the ZNBG device. These
capacitors are required for all stages used. Values of 10nF and 4.7nF respectively are
recommended however this is design dependent and any value between 1nF and 100nF could
be used.
The capacitors C
NB
and C
SUB
are an integral part of the ZNBGs negative supply generator. The
negative bias voltage is generated on-chip using an internal oscillator. The required value of
capacitors C
NB
and C
SUB
is 47nF. This generator produces a low current supply of approximately
-3 volts. Although this generator is intended purely to bias the external FETs, it can be used to
power other external circuits via the C
SUB
pin.
Resistors R
sets the drain current at which all external FETs are operated. Both ZNBG devices
have the facility to program different drain currents into selected FETs. Two R
inputs are
provided. For the ZNBG4000, resistor R
sets the drain current of FETs 1 and 2, resistor R
sets the drain current of FETs 3 and 4. For the ZNBG6000, resistor R
sets the drain current
of FETs 1 and 4, resistor R
sets the drain current of FETs 2, 3, 5 and 6. If the same drain current
is required for all FETs on either device then pins R
and R
can be wired together and
shunted to ground by a single calibration resistor of half normal value.
If any bias control circuit is not required, its related drain and gate connections may be left open
circuit without affecting the operation of the remaining bias circuits. If all FETs associated with
a current setting resistor are omitted, the particular R
should still be included. The supply
current can be reduced, if required, by using a high value R
CAL
resistor (e.g. 470k).
4-142
相關PDF資料 |
PDF描述 |
|---|---|
| ZNBG6000 | FET BIAS CONTROLLER |
| ZNBR4000 | DIODE MOD 1200V 2X120A TO-240AA |
| ZNBR4001Q16 | FET BIAS CONTROLLER |
| ZNBR6001Q20 | FET BIAS CONTROLLER |
| ZNBR6000Q20 | FET BIAS CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZNBG6001Q20 | 制造商:ZETEX 制造商全稱:ZETEX 功能描述:FET BIAS CONTROLLER |
| ZNBG6001Q20TC | 功能描述:接口 - 專用 6BIAS GENERATOR 2.0V RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| ZNBG6005Q20TC | 功能描述:MOSFET FIXED BIAS GENERATOR RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| ZNBR4000 | 制造商:ZETEX 制造商全稱:ZETEX 功能描述:FET BIAS CONTROLLER |
| ZNBR4000Q16 | 制造商:ZETEX 制造商全稱:ZETEX 功能描述:FET BIAS CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。