參數資料
型號: ZL10354QCF1
廠商: ZARLINK SEMICONDUCTOR INC
元件分類: 消費家電
英文描述: Diversity Enabled Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV (DTV)
中文描述: SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝: 7 X 7 MM, 1.40 MM HEIGHT, LEAD FREE, MS-026BBD, LQFP-64
文件頁數: 31/34頁
文件大?。?/td> 578K
代理商: ZL10354QCF1
ZL10354
Data Sheet
31
Zarlink Semiconductor Inc.
5.4.1.5 Oscillator/Clock Application Notes
On the printed circuit board, the tracks to the crystal and capacitors must be made as short as possible.
Other signal tracks must not be allowed to cross through this area. The component tracks should preferably
be ringed by a ground track connected to the chip ground (0 V) on adjacent pins either side of the crystal
pins. It is also advisable to provide a ground plane for the circuit to reduce noise.
External clock signals, applied to XTI and/or XTO, must not exceed the cell supply limits (i.e., 0V and CVDD)
and current into or out of XTI and/or XTO must be limited to less than 10mA to avoid damaging the cell’s
amplitude clamping circuit.
An external, DC coupled, single ended square wave clock signal may be applied to XTI if OSCMODE = 0. To
limit the current taken from the signal source a resistor should be placed between the clock source and XTI.
The recommended value for this series resistor is 470
for a clock signal switching between 0 V and
CVDD. The current the clock source needs to source/sink is then <1.9 mA. The XTO pin must be left
unconnected in this configuration.
AC coupling of a single ended external clock to XTI, with OSCMODE = 0, is not recommended. The duty
cycle of the OSCOUT signal cannot be guaranteed in such a configuration.
AC coupling of a single ended external clock to XTI, with OSCMODE = 1, is possible. It is recommended that
the circuit shown in Figure 15 be used to correctly bias the oscillator inputs: The common-mode voltage
VCM for XTI and XTO, (set by the 36 k
and 22 k
resistors) must be 800 mV < VCM < CVDD and the
amplitude Vpp of the clock signal must be >100 mV.
Figure 15 - External Clocking via AC Coupling
External, differential clock signals may be applied to XTI and XTO if OSCMODE = 1. The common-mode
voltage VCM for the differential clock signals must be 800 mV < VCM < CVDD, and the peak-to-peak signal
amplitude Vpp must be >100 mV. It is recommended that differential clock signals have VCM = 1.0V. For
Vpp > 400 mV a resistor of >390
in series with XTI or XTO may be required to limit the current taken from
or supplied to the clock sources.
External clock
10nF
XTI
100k
10nF
22k
36k
XTO
Vdd
OSCMODE
相關PDF資料
PDF描述
ZL10355 Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
ZL10355QCF Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
ZL10355QCF1 Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
ZL10355QCG Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
ZL10355QCG1 Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
相關代理商/技術參數
參數描述
ZL10354QCG 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Diversity Enabled Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV (DTV)
ZL10354QCG1 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Diversity Enabled Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV (DTV)
ZL10355 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
ZL10355QCF 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)
ZL10355QCF1 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV(DTV)