- 您現在的位置：買賣IC網 > PDF目錄372964 > Z86L92 (ZiLOG, Inc.) IR MICROCONTROLLER PDF資料下載
參數資料
| 型號： | Z86L92 |
| 廠商： | ZiLOG, Inc. |
| 英文描述： | IR MICROCONTROLLER |
| 中文描述： | 紅外單片機 |
| 文件頁數： | 50/71頁 |
| 文件大小： | 364K |
| 代理商： | Z86L92 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
Z86C72/C92/L72/L92
IR Microcontroller
Zilog
6-50
P R E L I M I N A R Y
DS97LVO0900
FUNCTIONAL DESCRIPTION
(Continued)
When more than one interrupt is pending, priorities are re-
solved by a programmable priority encoder controlled by
the Interrupt Priority register. An interrupt machine cycle is
activated when an interrupt request is granted. This dis-
ables all subsequent interrupts, saves the Program
Counter and Status Flags, and then branches to the pro-
gram memory vector location reserved for that interrupt.
All Z86L/CX2 interrupts are vectored through locations in
the program memory. This memory location and the next
byte contain the 16-bit address of the interrupt service rou-
tine for that particular interrupt request. To accommodate
polled interrupt systems, interrupt inputs are masked and
the Interrupt Request register is polled to determine which
of the interrupt requests need service.
An interrupt resulting from AN1 is mapped into IRQ2, and
an interrupt from AN2 is mapped into IRQ0. Interrupts
IRQ2 and IRQ0 may be rising, falling, or both edge trig-
gered, and are programmable by the user. The software
can poll to identify the state of the pin.
Programming bits for the Interrupt Edge Select are located
in the IRQ Register (R250), bits D7 and D6 . The configu-
ration is shown in Table 4.
Clock
. The Z86L/CX2 on-chip oscillator has a high-gain,
parallel-resonant amplifier for connection to a crystal, LC,
ceramic resonator, or any suitable external clock source
(XTAL1 = Input, XTAL2 = Output). The crystal should be
AT cut, 1 MHz to 8 MHz maximum, with a series resistance
(RS) less than or equal to 100 Ohms. The Z86L/CX2 on-
chip oscillator may be driven with a cost-effective RC net-
work or other suitable external clock source.
The crystal should be connected across XTAL1 and
XTAL2 using the recommended capacitors (capacitance
greater than or equal to 22 pF) from each pin to ground.
The RC oscillator configuration is an external resistor con-
nected from XTAL1 to XTAL2, with a frequency-setting ca-
pacitor from XTAL1 to ground (Figure 36).
Table 3. Interrupt Types, Sources, and Vectors
Name
IRQ0
Source
/DAV0, IRQ0
Vector
Location
0, 1
Comments
External (P32),
Rising Falling Edge
Triggered
External (P33),
Falling Edge
Triggered
External (P31),
Rising Falling Edge
Triggered
Internal
Internal
IRQ1
IRQ1
2, 3
IRQ2
/DAV2, IRQ2,
T
IN
4, 5
IRQ3
IRQ4
T16
T8
6, 7
8, 9
Table 4. IRQ Register
IRQ
Interrupt Edge
D7
0
0
1
1
D6
0
1
0
1
IRQ2 (P31)
F
F
R
R/F
IRQ0 (P32)
F
R
F
R/F
Notes:
F = Falling Edge
R = Rising Edge
In analog mode, the Stop-Mode Recovery sources selected
by the SMR register are connected to the IRQ1 input. Any of
the Stop-Mode Recovery sources for SMR (except P31, P32,
and P33) can be used to generate IRQ1 (falling edge trig-
gered)
相關PDF資料 |
PDF描述 |
|---|---|
| Z86L9208VSC | IR MICROCONTROLLER |
| Z87200 | CAP 0.047UF 100V 10% X7R AXIAL TR-14 |
| ZA3020 | 2A STEP DOWN PWM SWITCH MODE DC DC REGULATORS |
| ZA3020DS | 2A STEP DOWN PWM SWITCH MODE DC DC REGULATORS |
| ZC0302 | VGA & CIF USB PC Camera Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z86L9208FSC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| Z86L9208VSC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:IR MICROCONTROLLER |
| Z86L97 | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
| Z86L972 | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
| Z86L972HZ008SC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。