參數資料
型號: Z86E4016PSC
廠商: ZILOG INC
元件分類: 微控制器/微處理器
英文描述: Z8 4K OTP Microcontroller
中文描述: 8-BIT, OTPROM, MICROCONTROLLER, PDIP40
封裝: PLASTIC, DIP-40
文件頁數: 41/66頁
文件大?。?/td> 453K
代理商: Z86E4016PSC
Z86E30/E31/E40
Zilog
Z8 4K OTP Microcontroller
DS97Z8X0500
P R E L I M I N A R Y
41
1
When more than one interrupt is pending, priorities are re-
solved by a programmable priority encoder that is con-
trolled by the Interrupt Priority Register (IPR). An interrupt
machine cycle is activated when an interrupt request is
granted. Thus, disabling all subsequent interrupts, saves
the Program Counter and Status Flags, and then branches
to the program memory vector location reserved for that in-
terrupt. All interrupts are vectored through locations in the
program memory. This memory location and the next byte
contain the 16-bit starting address of the interrupt service
routine for that particular interrupt request.
To accommodate polled interrupt systems, interrupt inputs
are masked and the interrupt request register is polled to
determine which of the interrupt requests need service.
An interrupt resulting from AN1 is mapped into IRQ2, and
an interrupt from AN2 is mapped into IRQ0. Interrupts
IRQ2 and IRQ0 may be rising, falling or both edge trig-
gered, and are programmable by the user. The software
may poll to identify the state of the pin.
Programming bits for the Interrupt Edge Select are located
in bits D7 and D6 of the IRQ Register (R250). The config-
uration is shown in Table 11.
Clock.
The on-chip oscillator has a high-gain, parallel-res-
onant amplifier for connection to a crystal, RC, ceramic
resonator, or any suitable external clock source (XTAL1 =
Input, XTAL2 = Output). The crystal should be AT cut, 10
KHz to 16 MHz max, with a series resistance (RS) less
than or equal to 100 Ohms.
The crystal should be connected across XTAL1 and
XTAL2 using the vendor's recommended capacitor values
from each pin directly to device pin Ground. The RC oscil-
lator option can be selected in the programming mode.
The RC oscillator configuration must be an external resis-
tor connected from XTAL1 to XTAL2, with a frequency-set-
ting capacitor from XTAL1 to Ground (Figure 29).
Table 11. IRQ Register Configuration
IRQ
Interrupt Edge
D7
0
0
1
1
D6
0
1
0
1
P31
F
F
R
R/F
P32
F
R
F
R/F
Notes:
F = Falling Edge
R = Rising Edge
Figure 29. Oscillator Configuration
XTAL1
XTAL2
C1
C2
C1
C2
C1
XTAL1
XTAL2
XTAL1
XTAL2
XTAL1
XTAL2
Ceramic Resonator or
Crystal
C1, C2 = 47 pF TYP *
F = 8 MHz
LC
C1, C2 = 22 pF
L = 130
μ
H *
F = 3 MHz *
RC
@ 5V Vcc (TYP)
C1 = 100 pF
R = 2K
F = 6 MHz
External Clock
L
R
* Typical value including pin parasitics
相關PDF資料
PDF描述
Z86E4016PSE Z8 4K OTP Microcontroller
Z86E4016VSC Z8 4K OTP Microcontroller
Z86E3016SEC Z8 4K OTP Microcontroller
Z86E3016ESE Z8 4K OTP Microcontroller
Z86E3016PSC Z8 4K OTP Microcontroller
相關代理商/技術參數
參數描述
Z86E4016PSE 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Z8 4K OTP Microcontroller
Z86E4016PSG 功能描述:8位微控制器 -MCU Z8 4K OTP 16MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
Z86E4016VEC 功能描述:8位微控制器 -MCU 4K OTP 16MHz XTEMP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
Z86E4016VEC00TR 功能描述:IC Z8 MCU OTP 4K 44PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:Z8® 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
Z86E4016VEE 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Z8 4K OTP Microcontroller