- 您現在的位置：買賣IC網 > PDF目錄372963 > Z86E3016KEC (ZiLOG, Inc.) Z8 4K OTP Microcontroller PDF資料下載
參數資料
| 型號： | Z86E3016KEC |
| 廠商： | ZiLOG, Inc. |
| 英文描述： | Z8 4K OTP Microcontroller |
| 中文描述： | Z8 4K的檢察官辦公室單片機 |
| 文件頁數： | 25/66頁 |
| 文件大小： | 453K |
| 代理商： | Z86E3016KEC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Z86E30/E31/E40
Zilog
Z8 4K OTP Microcontroller
DS97Z8X0500
P R E L I M I N A R Y
25
1
Port 0
(P07-P00). Port 0 is an 8-bit, bidirectional, CMOS-
compatible I/O port. These eight I/O lines can be config-
ured under software control as a nibble I/O port, or as an
address port for interfacing external memory. The input
buffers are Schmitt-triggered and nibble programmed. Ei-
ther nibble output that can be globally programmed as
push-pull or open-drain. Low EMI output buffers can be
globally programmed by the software. Port 0 can be placed
under handshake control. In Handshake Mode, Port 3
lines P32 and P35 are used as handshake control lines.
The handshake direction is determined by the configura-
tion (input or output) assigned to Port 0's upper nibble. The
lower nibble must have the same direction as the upper
nibble.
For external memory references, Port 0 provides address
bits A11-A8 (lower nibble) or A15-A8 (lower and upper nib-
ble) depending on the required address space. If the ad-
dress range requires 12 bits or less, the upper nibble of
Port 0 can be programmed independently as I/O while the
lower nibble is used for addressing. If one or both nibbles
are needed for I/O operation, they must be configured by
writing to the Port 0 mode register. In ROMless mode, after
a hardware reset, Port 0 is configured as address lines
A15-A8, and extended timing is set to accommodate slow
memory access. The initialization routine can include re-
configuration to eliminate this extended timing mode. In
ROM mode, Port 0 is defined as input after reset.
Port 0 can be set in the High-Impedance Mode if selected
as an address output state, along with Port 1 and the con-
trol signals /AS, /DS, and R//W (Figure 18).
相關PDF資料 |
PDF描述 |
|---|---|
| Z86E3016KEE | Z8 4K OTP Microcontroller |
| Z86E3016PEC | Z8 4K OTP Microcontroller |
| Z86E3016PEE | Z8 4K OTP Microcontroller |
| Z86E3016PSE | Z8 4K OTP Microcontroller |
| Z86E3016VSC | Z8 4K OTP Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z86E3016KEE | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Z8 4K OTP Microcontroller |
| Z86E3016KSC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Z8 4K OTP Microcontroller |
| Z86E3016KSE | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Z8 4K OTP Microcontroller |
| Z86E3016PEC | 功能描述:8位微控制器 -MCU 8K OTP 16MHZ W/UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| Z86E3016PEE | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Z8 4K OTP Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。