- 您現在的位置：買賣IC網 > PDF目錄373752 > Z0220516SSCR4292 (ZILOG INC) Low Power Modem Controller(低功耗單片調制解調器控制器) PDF資料下載
參數資料
| 型號： | Z0220516SSCR4292 |
| 廠商： | ZILOG INC |
| 元件分類： | 調制器/解調器 |
| 英文描述： | Low Power Modem Controller(低功耗單片調制解調器控制器) |
| 中文描述： | 1.2 kbps DATA, MODEM-SUPPORT CIRCUIT, PDSO28 |
| 封裝： | SOIC-28 |
| 文件頁數： | 17/30頁 |
| 文件大?。?/td> | 226K |
| 代理商： | Z0220516SSCR4292 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Z02205
ZiLOG
Modem Controller
PS001000-MOD0599
15
M
Speaker On/Off Options
The country configuration may disable the speaker. If so, this command returns an
ERROR result.
M0
Speaker always off.
M1
Speaker on until carrier detected. This is the default value in North
America.
M2
Speaker always on; stays on after carrier is detected.
M3
Speaker off as digits are dialled, but on during ringback and on until carrier
signal is detected.
This command returns the modem to the on-line mode. It is frequently used after the
escape character sequence (+++) to resume communication with the remote modem. If
handshaking is started, the modem uses Originate or Answer mode handshaking,
depending upon whether the modem originated or answered the telephone call.
O0
Returns the modem to the On-Line state from the Command state during a
telephone line connection. The modem starts handshaking if no telephone
line connection and the modem was off hook.
O1
Returns the modem to the On-Line state and retrain its data pump during a
telephone line connection. The modem starts handshaking if there was no
telephone line connection is detected but the modem was OFF-HOOK.
Sets cadence of pulse dial. The country configuration may disable this command,
forcing particular pulse dialing parameters. In this event, the modem returns an ERROR
result if this command is issued.
&P0
39%/61% make/break ratio and 10 pulses per second when pulse dialing.
This is the default value.
&P1
33%/67% make/break ratio and 10 pulses per second when pulse dialing.
&P2
39%/61% make/break ratio and 20 pulses per second when pulse dialing.
&P3
33%/67% make/break ratio and 20 pulses per second when pulse dialing.
This command allows the user to either display result codes or to not display result
codes.
Q0
Result codes are displayed. This is the default value for North America.
Q1
Result codes are not displayed.
The &Q command selects the terminal communication mode.
&Q0
Asynchronous. The modem handshakes as the originator if S-register S0
is 0, and as the answerer if S0 is 1. This is the default value for North
America.
&Q1
Synchronous. Hangs up if DTR goes from on to off after the time in S-
register S25 after the CONNECT result code has been sent to the terminal.
This command sets the current S-register to the value
n
selected by the user. For
example, ATS7 will set the current S-register to S7. Default value is 0. Sn addresses a
particular S-register number so future commands like and = will read of write the S-
register. Modem reset and the &F command select S0 as the default S-register.
This command displays the value of the last S-register named in the Sn command.
This command writes the value x to the last S-register named in the Sn command. The
range of valid values for x depends upon which S-register is being written. 0 is assumed
if no value is given for x.
Selects the tone method of dialing.
This command changes the result code display format
V0
All result codes are displayed as numbers.
V1
All result codes are displayed as words (verbose form). This is the default
value for North America.
O
Return to On-Line
Mode
&P
Pulse Dial Make/Break
Ratios
Q
Result Code Display
Options
&Q
Communications Mode
Options
Sn
Set the current S-register
to n
=x
Read an S-Register
Write an S-register
T
V
Tone dialing
Result Code Format
Table 2. AT Command Set (Continued)
Command
Function and Description
相關PDF資料 |
PDF描述 |
|---|---|
| Z02205 | Modem Controller(低功耗單片modem) |
| Z02215 | Synchronous Single-chip V.22bis Modem(同步單片V.22Bis調制解調器) |
| Z02922 | Synchronous Single-chip Modem(同步單片調制解調器) |
| Z02W10 | surface mount silicon Zener diodes |
| Z02W10V | surface mount silicon Zener diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z0220516SSCR4292T | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:MODEM CONTROLLER IDEAL FOR LOW POWER CONSUMPTION, SMALL SIZE REQUIREMENTS |
| Z0220516SSCR4292TR | 功能描述:IC MODEM CTRL 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| Z0220516SSG1961 | 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Z0220516SSGR3641 | 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Z0220516SSGR4259 | 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。