- 您現在的位置：買賣IC網 > PDF目錄48085 > YE2C POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.24A (COIL), 6VDC (COIL), 1440mW (COIL), 5A (CONTACT), 28VDC (CONTACT), PANEL MOUNT PDF資料下載
參數資料
| 型號： | YE2C |
| 元件分類： | 功率/信號繼電器 |
| 英文描述： | POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.24A (COIL), 6VDC (COIL), 1440mW (COIL), 5A (CONTACT), 28VDC (CONTACT), PANEL MOUNT |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 3319K |
| 代理商： | YE2C |
Application notes
N°007
SUPPRESSOR DEVICES FOR RELAY COILS
The inductive nature of relay coils allows them to create magnetic forces which are converted to mechanical movements to
operate contact systems. When voltage is applied to a coil, the resulting current generates a magnetic flux, creating
mechanical work. Upon deenergizing the coil, the collapasing magnetic field induces a reverse voltage (also known as back
EMF) which tends to maintain current flow in the coil. The induced voltage level mainly depends on the duration of the
deenergization. The faster the switch-off, the higher the induced voltage.
All coil suppression networks are based on a reduction of speed of current decay. This reduction may also slow down the
opening of contacts, adversly effecting contact life and reliability. Therefore, it is very important to have a clear understanding
of these phenomena when designing a coil suppression circuitry.
Typical coil characteristics
On the graph below, the upper record shows the contacts state. (High level NO contacts closed, low level NC contacts closed,
intermediate state contact transfer). The lower record shows the voltage across the coil when the current is switched off by
another relay contact.
The surge voltage is limited to -300V by the arc generated across contact poles. Discharge duration is about 200
mircoseconds after which the current change does not generate sufficient voltage. The voltage decreases to the point where
the contacts start to move, at this time, the voltage increases due to the energy contained in the NO contact springs. The
voltage decreases again during transfer, and increases once more when the magnetic circuit is closed on permanent magnet.
Operating times are as follows:
Time to start the movement 1.5ms
Total motion time 2.3ms
Transfer time 1.4ms
Contact State
Date of issue: 6/00
- 8 -
Page 1 of 4
相關PDF資料 |
PDF描述 |
|---|---|
| YE2M | POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.038A (COIL), 48VDC (COIL), 1824mW (COIL), 5A (CONTACT), 28VDC (CONTACT), PANEL MOUNT |
| YE2N | POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.07A (COIL), 28VDC (COIL), 1960mW (COIL), 5A (CONTACT), 28VDC (CONTACT), PANEL MOUNT |
| YE2R | POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.12A (COIL), 12VDC (COIL), 1440mW (COIL), 5A (CONTACT), 28VDC (CONTACT), PANEL MOUNT |
| YE2V | POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.24A (COIL), 6VDC (COIL), 1440mW (COIL), 5A (CONTACT), 28VDC (CONTACT), PANEL MOUNT |
| YE4A | POWER/SIGNAL RELAY, 4PDT, MOMENTARY, 0.07A (COIL), 28VDC (COIL), 1960mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YE-2R14-D6 | 制造商:Honeywell Sensing and Control 功能描述: |
| YE2RBA2 | 制造商:Honeywell Sensing and Control 功能描述:MICRO SWITCH, PLUNGER, SPST-NO, 25A 250V; Contact Configuration:SPST-NO; Microswitch Type:Standard; Actuator Style:Plunger; Switch Operation:-; Operating Force Max:22ozf; Contact Voltage AC Nom:250V; Contact Current Max:25A ;RoHS Compliant: Yes |
| YE-2RB-A2 | 功能描述:基本/快動開關 BASIC SW SPNO 25 A 250Vac Overtrav PLGR RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| YE2RBA4 | 制造商:HONEYWELL 功能描述:Large Basics 制造商:Honeywell Sensing and Control 功能描述:Large Basics |
| YE-2RB-A4 | 功能描述:基本/快動開關 SP-NO CIR 20A 250Vac OVTR Pin Plung ACTR RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
發布緊急采購，3分鐘左右您將得到回復。