- 您現在的位置：買賣IC網 > PDF目錄9997 > XRT83L34IVTR (Exar Corporation)IC LIU T1/E1/J1 QUAD 128TQFP PDF資料下載
參數資料
| 型號： | XRT83L34IVTR |
| 廠商： | Exar Corporation |
| 文件頁數： | 51/99頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 QUAD 128TQFP |
| 標準包裝： | 750 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-TQFP（14x20） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
xr
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1
52
OPERATING THE MICROPROCESSOR INTERFACE IN THE INTEL-ASYNCHRONOUS MODE
If the Microprocessor Interface has been configured to operate in the Intel-Asynchronous Mode, then the
following Microprocessor Interface pins will assume the role that is described below in Table 17.
TABLE 17: THE ROLES OF THE VARIOUS MICROPROCESSOR INTERFACE PINS, WHEN CONFIGURED TO OPERATE IN
THE
INTEL-ASYNCHRONOUS MODE
PIN NAME
DESCRIPTION
TYPE
PIN/BALL
ALE/AS
Address Latch Enable - ALE:
If the Microprocessor Interface has been configured to operate in
the Intel-Asynchronous Mode, then this active-high input pin is
used to latch the data (residing on the Address Bus, A[6:0]) into the
MIcroprocessor Interface circuitry of the XRT83L34 device and to
indicate the start of a READ or WRITE cycle.
Pulling this input pin "HIGH" enables the input bus drivers for the
Address Bus input pins. The contents of the Address Bus will be
latched into the Microprocessor Interface circuitry upon the falling
edge of this input signal.
I
71
RD*/DS*
Read Strobe Input - RD*:
If the Microprocessor Interface is operating in the Intel-Asynchro-
nous Mode, then this input pin will function as the RD* (Active-Low
READ Strobe) input signal from the Microprocessor. Once this
active-low signal is asserted, then the XRT83L34 device will place
the contents of the addressed register on the Microprocessor Inter-
face Bi-Directional Data Bus (D[7:0]). When this signal is negated,
then the Bi-Directional Data Bus will be tri-stated.
I
70
RDY_DTACK* Active Low READY Output pin - RDY:
If the Microprocessor Interface has been configured to operate in
the Intel-Asynchronous Mode, then this output pin will function as
the "active-low" READY output.
During a READ or WRITE cycle, the Microprocessor Interface
block will toggle this output pin to the logic "LOW" level, ONLY
when it (the Microprocessor Interface) is ready to complete or ter-
minate the current READ or WRITE cycle. Once the Microproces-
sor has determined that this input pin has toggled to the logic
"LOW" level, then it is now safe for it to move on and execute the
next READ or WRITE cycle.
If (during a READ or WRITE cycle) the Microprocessor Interface
block is holding this output pin at a logic "HIGH" level, then the
Microprocessor is expected to extend this READ or WRITE cycle,
until it detects this output pin being toggled to the logic "LOW"
level.
O
73
WR*/R/W*
Write Strobe Input - WR*:
If the Microprocessor Interface is configured to operate in the Intel-
Asynchronous Mode, then this input pin functions as the WR*
(Active LOW WRITE Strobe) input signal from the Microprocessor.
Once this active-low signal is asserted, then the input buffers
(associated with the Bi-Directional Data bus, D[7:0]) will be
enabled. The Microprocessor Interface will latch the contents on
the Bi-Directional Data Bus (into the "target" register or address
location, within the XRT83L34 device) upon the rising edge of this
input pin.
I
69
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B6H-MX-B1 | CONVERTER MOD DC/DC 52V 75W |
| IDT72V841L15PFI8 | IC FIFO SYNC 2048X18 15NS 64QFP |
| VI-22V-MY | CONVERTER MOD DC/DC 5.8V 50W |
| MS3106R28-15S | CONN PLUG 35POS STRAIGHT W/SCKT |
| VE-JNL-MX-S | CONVERTER MOD DC/DC 28V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83L34IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38ES | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83L38ES-BG | 功能描述:界面開發工具 Eval System for XRT83L38 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。