參數資料
型號： XRT75VL00DIVTR
廠商： Exar Corporation
文件頁數： 31/92頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 1CH 52TQFP
標準包裝： 1,000
類型： 線路接口裝置（LIU）
驅動器/接收器數： 1/1
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 52-LQFP
供應商設備封裝： 52-TQFP（10x10）
包裝： 帶卷 (TR)
XRT75VL00D
32
REV. 1.0.4
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
6.0
JITTER:
There are three fundamental parameters that describe circuit performance relative to jitter:
Jitter Tolerance (Receiver)
Jitter Transfer (Receiver/Transmitter)
Jitter Generation
6.1
JITTER TOLERANCE - RECEIVER:
Jitter tolerance is a measure of how well a Clock and Data Recovery unit can successfully recover data in the
presence of various forms of jitter. It is characterized by the amount of jitter required to produce a specified bit
error rate. The tolerance depends on the frequency content of the jitter. Jitter Tolerance is measured as the
jitter amplitude over a jitter spectrum for which the clock and data recovery unit achieves a specified bit error
rate (BER). To measure the jitter tolerance as shown in Figure 21, jitter is introduced by the sinusoidal
modulation of the serial data bit sequence.
Input jitter tolerance requirements are specified in terms of compliance with jitter mask which is represented as
a combination of points.Each point corresponds to a minimum amplitude of sinusoidal jitter at a given jitter
frequency.
6.1.1
DS3/STS-1 Jitter Tolerance Requirements:
Bellcore GR-499 CORE, Issue 1, December 1995 specifies the minimum requirement of jitter tolerance for
Category I and Category II. The jitter tolerance requirement for Category II is the most stringent. Figure 22
shows the jitter tolerance curve as per GR-499 specification along with the measured performance for the
device.
FIGURE 21. JITTER TOLERANCE MEASUREMENTS
FREQ
Synthesizer
FREQ
Synthesizer
Pattern
Generator
Pattern
Generator
DUT
XRT75VL00D
DUT
XRT75VL00D
Error
Detector
Error
Detector
Modulation
Freq.
Data
Clock
相關PDF資料
PDF描述
MS27468T9B35S EDR CONN RCPT 6POS JAM NUT W/SCKT
MS27466T23B35SD CONN RCPT 100POS WALL MNT W/SCKT
MS27466E15A35P CONN RCPT 37POS WALL MNT W/PINS
VI-B40-IV-F1 CONVERTER MOD DC/DC 5V 150W
MS27497T10B5PA CONN RCPT 5POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
XRT75VL00DIVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00ES 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+A 3.3V VOLTAGE DRIVE RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00IV 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75VL00IV-F 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75VL00IVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*