參數資料
型號： XRT75VL00DIV
廠商： EXAR CORP
元件分類： 數字傳輸電路
英文描述： E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： DATACOM, PCM TRANSCEIVER, PQFP52
封裝： 10 X 10 MM, TQFP-52
文件頁數： 31/92頁
文件大?。?/td> 816K
代理商： XRT75VL00DIV
XRT75VL00D
32
REV. 1.0.4
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
6.0
JITTER:
There are three fundamental parameters that describe circuit performance relative to jitter:
Jitter Tolerance (Receiver)
Jitter Transfer (Receiver/Transmitter)
Jitter Generation
6.1
JITTER TOLERANCE - RECEIVER:
Jitter tolerance is a measure of how well a Clock and Data Recovery unit can successfully recover data in the
presence of various forms of jitter. It is characterized by the amount of jitter required to produce a specified bit
error rate. The tolerance depends on the frequency content of the jitter. Jitter Tolerance is measured as the
jitter amplitude over a jitter spectrum for which the clock and data recovery unit achieves a specified bit error
rate (BER). To measure the jitter tolerance as shown in Figure 21, jitter is introduced by the sinusoidal
modulation of the serial data bit sequence.
Input jitter tolerance requirements are specified in terms of compliance with jitter mask which is represented as
a combination of points.Each point corresponds to a minimum amplitude of sinusoidal jitter at a given jitter
frequency.
6.1.1
DS3/STS-1 Jitter Tolerance Requirements:
Bellcore GR-499 CORE, Issue 1, December 1995 specifies the minimum requirement of jitter tolerance for
Category I and Category II. The jitter tolerance requirement for Category II is the most stringent. Figure 22
shows the jitter tolerance curve as per GR-499 specification along with the measured performance for the
device.
FIGURE 21. JITTER TOLERANCE MEASUREMENTS
FREQ
Synthesizer
FREQ
Synthesizer
Pattern
Generator
Pattern
Generator
DUT
XRT75VL00D
DUT
XRT75VL00D
Error
Detector
Error
Detector
Modulation
Freq.
Data
Clock
相關PDF資料
PDF描述
XRT75VL00D E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT83SL34IV QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL34 QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XS2F-A422-90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-A90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
相關代理商/技術參數
參數描述
XRT75VL00DIV-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00DIVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00DIVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00ES 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+A 3.3V VOLTAGE DRIVE RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00IV 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*