參數資料
型號: XRT75R03IV
廠商: Exar Corporation
文件頁數: 18/92頁
文件大?。?/td> 0K
描述: IC LIU E3/DS3/STS-1 3CH 128LQFP
標準包裝: 72
類型: 線路接口裝置(LIU)
驅動器/接收器數: 3/3
規(guī)程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 128-LQFP
供應商設備封裝: 128-LQFP(14x20)
包裝: 托盤
xr
XRT75R03
THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.8
22
67
SClk/TCLKINV
I
Microprocessor Serial Interface -Serial Clock Input:
This input pin functions as the Clock Source for the Microprocessor Serial Inter-
face.
Each time the user wishes to perform a READ or WRITE operate with the on-
chip Command Registers via the Microprocessor Serial Interface, the user
MUST do the following.
Assert the CS input pin by toggling it "Low", and
Provide 16 Clock Periods to this particular input pin for each READ and
WRITE operation.
The Microprocessor Serial Interface will sample any data residing upon the SDI
input pin, upon the rising edge of this clock signal. Further, for READ opera-
tions, the Microprocessor Serial Interface will serially output the contents of a
target Command Register upon the falling edge of this clock signal.
NOTE: The maximum frequency of this particular clock signal is 10MHz.
66
CS/RCLKINV
I
Microprocessor Serial Interface - Chip Select Input:
This input pin should be pulled "Low" whenever a READ or WRITE operation is
to be executed to the on-chip Command Registers, via the Microprocessor
Serial Interface.
This input pin should remain "Low" until the READ or WRITE operation has
been completed. This input pin should be pulled "High" at all other times.
NOTE: If the XRT75R03 has been configured to operate in the Host Mode then
this input pin will function as the RCLKINV input pin.
71
INT/LOSMUT
O
Microprocessor Serial Interface - Interrupt Request Output:
If the XRT75R03 has been configured to operate in the Host Mode, then this pin
becomes the Interrupt Request Output for the XRT75R03.
During normal conditions, this output pin will be pulled "High". However, if the
user enables certain interrupts within the device, and if those conditions occur,
then the XRT75R03 will request an interrupt from the Microprocessor by tog-
gling this output pin "Low".
NOTES:
1.
If the XRT75R03 device is configured to operate in the Hardware
Mode, then this pin functions as the LOSMUT input pin.
2.
This pin will remain "Low" until the Interrupt has been served.
101
RESET
I
Microprocessor Serial Interface - H/W RESET Input:
Pulsing this input "Low" causes the XRT75R03 to reset the contents of the on-
chip Command Registers to their default values. As a consequence, the
XRT75R03 will then also be operating in its default condition.
For normal operation pull this input pin to a logic "High".
NOTE: This input pin is internally pulled high.
POWER SUPPLY AND GROUND PINS
PIN #
PIN NAME
TYPE
DESCRIPTION
RECEIVE ANALOG VDD
77
93
86
RxAVDD_0
RxAVDD_1
RxAVDD_2
****
Microprocessor Serial INTERFACE - (HOST MODE)
PIN #
SIGNAL NAME
TYPE
DESCRIPTION
相關PDF資料
PDF描述
MS3101F24-28P CONN RCPT 24POS FREE HNG W/PINS
IDT72V821L10PF IC FIFO SYNC 512X9X2 10NS 64QFP
MS27473T14F18SA CONN PLUG 18POS STRAIGHT W/SCKT
IDT72V821L15TFI IC FIFO SYNC 512X9X2 15NS 64QFP
IDT72V821L10TF IC FIFO SYNC 512X9X2 10NS 64QFP
相關代理商/技術參數
參數描述
XRT75R03IV-F 功能描述:外圍驅動器與原件 - PCI 3-Ch E3/DS3/STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R03IVTR 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03IVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R06 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R06D 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER