PIN
參數資料
型號: XRT75L02DIV-F
廠商: Exar Corporation
文件頁數: 49/50頁
文件大?。?/td> 0K
描述: IC LIU E3/DS3/STS-1 2CH 100TQFP
標準包裝: 90
類型: 線路接口裝置(LIU)
驅動器/接收器數: 2/2
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-TQFP(14x14)
包裝: 托盤
xr
XRT75L02
REV. 1.0.3
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
6
RECEIVE INTERFACE
PIN #
SIGNAL NAME
TYPE
DESCRIPTION
1
25
REQEN_0
REQEN_1
I
Receive Equalization Enable Input - Channel 0:
Receive Equalization Enable Input - Channel 1:
Setting this input pin "High" enables the Internal Receive Equalizer of
Channel_n. Setting this pin "Low" disables the Internal Receive Equalizer.
NOTES:
1.
This input pin is ignored and should be connected to GND if the
XRT75L02 is operating in the HOST Mode
2.
This pin is internally pulled down.
31
RxON/
SDI
I
Hardware Mode: Receiver Turn ON Input
Host Mode: Serial Data Input:
Function of this pin depends on whether the XRT75L02 is configured to operate
in Hardware mode or Host mode.
In Hardware mode, setting this input pin “High” turns on and enables the
Receivers of all the channels.
NOTES:
1.
If the XRT75L02 is configured in HOST mode, this pin functions as
SDI input pin (please refer to the pin description for Microprocessor
Interface)
2.
This pin is internally pulled down.
27
RxMON/
SDO
I
Hardware Mode: Receive Monitoring Mode
Host Mode: Serial Data Output:
In Hardware mode, when this pin is tied “High” all 2 channels configure into
monitoring channels. In the monitoring mode, the Receiver is capable of moni-
toring the signals with 20 dB flat loss plus 6 dB cable attenuation. This allows
monitoring very weak signal, however the internal LOS circuitry is suppressed
and LOS will never assert nor LOS be declared when operating under this
mode.
In HOST Mode each channel can be independently configured to be a monitor-
ing channel by setting the bits in the channel control registers.
NOTE: If the XRT75L02 is configured in HOST mode, this pin functions as SDO
pin (please refer to the pin description for the Microprocessor Interface).
91
36
RxCLK_0
RXCLK_1
O
Receive Clock Output - Channel 0:
Receive Clock Output - Channel 1:
By default, RPOS and RNEG data sampled on the rising edge RxCLK..
Set the RxCLKINV bit or tie RClkINV pin “High” to sample RPOS/RNEG data
on the falling edge of RxCLK
92
35
RPOS_0
RPOS_1
O
Receive Positive Data Output - Channel 0:
Receive Positive Data Output - Channel 1:
NOTE: If the B3ZS/HDB3 Decoder is enabled in Single-rail mode, then the zero
suppression patterns in the incoming line signal (such as: "00V",
"000V", "B0V", "B00V") is removed and replaced with ‘0’.
相關PDF資料
PDF描述
XRT75L03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75L03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75L04DIV-F IC LIU E3/DS3/STS-1 4CH 176TQFP
XRT75L04IV-F IC LIU E3/DS3/STS-1 4CH 176LQFP
XRT75L06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
相關代理商/技術參數
參數描述
XRT75L02DIVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02ES 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02IV 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L02IV-F 功能描述:網絡控制器與處理器 IC 2-Ch DS3, E3, STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75L02IVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel