- 您現在的位置：買賣IC網 > PDF目錄1976 > XRT73LC04AIV-F (Exar Corporation)IC LIU E3/DS3/STS-1 4CH 144LQFP PDF資料下載
參數資料
| 型號： | XRT73LC04AIV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 27/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| 標準包裝： | 60 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
XRT73LC04A
29
REV. 1.0.2
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
TxClk_(n) is the clock signal that is of the selected
data rate frequency, E3 = 34.368 MHz, DS3 = 44.736
MHz and STS-1 = 51.84 MHz. If the Transmit Section
samples a "1" on the TPData_(n) input pin, then the
Transmit Section of the device generates a positive
polarity pulse via the TTIP_(n) and TRing_(n) output
pins across a 1:1 transformer. If the Transmit Section
samples a "1" on the TNData_(n) input pin, then the
Transmit Section of the device generates a negative
polarity pulse via the TTIP_(n) and TRing_(n) output
pins across a 1:1 transformer.
2.1.2
Accepting Single-Rail Data from the Ter-
minal Equipment
To transmit data in a Single-Rail data from the Termi-
nal Equipment, configure the XRT73LC04A in the
HOST Mode.
To Configure Channel(n) to accept Single-Rail Da-
ta from the Terminal Equipment:
Write a "1" into the (SR/DR)_(n) bit-field, within Com-
mand Register CR3-(n) shown below. (Please refer
toTable 2 for the Address of the individual (n) chan-
nel.
The Transmit Section (of each channel) samples this
input pin on the falling edge of the TxClk_(n) clock
signal and encodes this data into the appropriate bi-
polar line signal across the TTIP_(n) and TRing_(n)
output pins.
NOTES:
1. In this mode, the Transmit Logic Block ignores the
TNData_(n) input pin.
2. If the Transmit Section of a given channel is config-
ured to accept Single-Rail data from the Terminal
Equipment, the B3ZS/HDB3 Encoder must be
enabled.
Figure 16 Illustrates the behavior of the TPData_(n)
and TxClk_(n) signals when the Transmit Logic Block
has been configured to accept Single-Rail data from
the Terminal Equipment.
2.2
THE TRANSMIT CLOCK DUTY CYCLE ADJUST CIR-
CUITRY
The on-chip Pulse-Shaping circuitry within the Trans-
mit Section of each Channel in the XRT73LC04A
generates pulses of the appropriate shapes and
width to meet the applicable pulse template require-
ments. The widths of these output pulses are defined
by the width of the half-period pulses within the
TxClk_(n) signal.
However, if the widths of the pulses within the
TxClk_(n) clock signal are allowed to vary significant-
ly, this could jeopardize the chip's ability to generate
Transmit Output pulses of the appropriate width and
thereby not meet the Pulse Template requirement
specification. Consequently, the chip's ability to gen-
erate compliant pulses could depend upon the duty
cycle of the clock signal applied to the TxClk_(n) input
pin.
The Transmit Clock Duty Cycle Adjust Circuitry ac-
cepts clock pulses via the TxClk_(n) input pin at duty
cycles ranging from 30% to 70% and converts them
to a 50% duty cycle.
2.3
THE HDB3/B3ZS ENCODER BLOCK
The purpose of the HDB3/B3ZS Encoder Block is to
aid in the Clock Recovery process at the Remote Ter-
minal Equipment by ensuring an upper limit on the
number of consecutive zeros that can exist within the
line signal.
2.3.1
B3ZS Encoding
If the XRT73LC04A has been configured to operate in
the DS3 or SONET STS-1 Modes, then the HDB3/
B3ZS Encoder blocks operate in the B3ZS Mode.
When the Encoder is operating in this mode, it pars-
es through and searches the Transmit Binary Data
Stream from the Transmit Logic Block for the occur-
COMMAND REGISTER CR3-(n)
D4
D3
D2
D1
D0
(SR/DR)_(n) LOSMUT_(n) RxOFF RxClk_(n)INV Reserved
1
x
FIGURE 16. THE BEHAVIOR OF THE TPDATA AND TXCLK INPUT SGNALS, WHILE THE TRANSMIT LOGIC BLOCK IS
ACCEPTING SINGLE-RAIL DATA FROM THE TERMINAL EQUIPMENT
TxClk
TPData
Data
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75L00DIV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L02DIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73R06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73R06ES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73R06IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73R06IB-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73R12 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。