參數資料
型號: XRT73L04BIV
廠商: EXAR CORP
元件分類: 數字傳輸電路
英文描述: 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
中文描述: DATACOM, PCM TRANSCEIVER, PQFP144
封裝: 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144
文件頁數: 55/64頁
文件大?。?/td> 359K
代理商: XRT73L04BIV
XRT73L04B
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.1
51
When the Transmit Drive Monitor circuitry within a
given line is connected to the line, as illustrated in
Figure 36, then it monitors the line for transitions. As
long as the Transmit Drive Monitor circuitry detects
transitions on the line via the MTIP_(n) and
MRing_(n) pins, then it keeps the DMO (Drive Moni-
tor Output) signal "Low". If the Transmit Drive Moni-
tor circuit detects no transitions on the line for 128+32
TxClk periods, then the DMO (Drive Monitor Output)
signal toggles "High".
N
OTE
:
The Transmit Drive Monitor circuit does not have to
be used to operate the Transmit Section of the XRT73L04B.
This is purely a diagnostic feature.
4.6
T
HE
TAOS (T
RANSMIT
A
LL
O
NE
S) F
EATURE
The XRT73L04B can command any channel to trans-
mit an all “1’s" pattern onto the line by toggling a sin-
gle input pin or by setting a single bit-field within one
of the Command Registers to "1".
N
OTE
:
When this feature is activated, the Transmit Section
of the configured channel overwrites the Terminal Equip-
ment data with this all “1’s" pattern.
a. Operating in the Hardware Mode
Configure Channel(n) to transmit an all “1’s" pattern
by toggling the TAOS_(n) input pin (pin 45, 46, 135 or
136) “High". Terminate the all “1’s" pattern by tog-
gling the TAOS_(n) input pin “Low".
b. Operating in the HOST Mode
Configure Channel(n) to transmit an all “1’s" pattern
by writing to Command Register CR1-(n) and setting
the TAOS_(n) bit-field (bit D3) to "1".
COMMAND REGISTER CR1-(n)
Terminate the all “1’s" pattern by writing to Command
Register CR1-(n) and setting the TAOS_(n) bit-field
(D3) to "0".
5.0
THE MICROPROCESSOR SERIAL INTER-
FACE
The on-chip Command Registers of XRT73L04B
DS3/E3/STS-1 Line Interface Unit IC are used to con-
figure the XRT73L04B into a wide-variety of modes.
This section discusses the following:
1. The description of the Command Registers.
2. A description on how to use the Microprocessor
Serial Interface.
5.1
D
ESCRIPTION
OF
THE
C
OMMAND
R
EGISTERS
(repeated as Table 7), lists the Command Registers,
their Addresses and their bit-formats.
F
IGURE
36. T
HE
XRT73L04B
EMPLOYING
THE
T
RANSMIT
D
RIVE
M
ONITOR
F
EATURES
R1 = 31.6
R2 = 31.6
Channel (n)
TxPOS_(n)
TxNEG_(n)
TxLineClk_(n)
TTIP_(n)
TRing_(n)
TPData_(n)
TNData_(n)
TxClk_(n)
Only One Channel Shown
1:1
J1
BNC
MTIP_(n)
MRing_(n)
R3 = 270
R4 = 270
D4
D3
D2
D1
D0
TxOFF_(n) TAOS_(n) TxClkINV_(n) TxLEV_(n) Reserved
0
1
X
X
X
相關PDF資料
PDF描述
XRT73L04 4 Channel E3/DS3/STS-1 Line Interface Unit(4通道 E3/DS3/STS-1線接口單元)
XRT73L06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73LC00A E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73LC00AIV E3/DS3/STS-1 LINE INTERFACE UNIT
相關代理商/技術參數
參數描述
XRT73L04BIV-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73L06 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L06ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73L06IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73L06IB-F 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59