- 您現在的位置：買賣IC網 > PDF目錄376461 > XRT73L03AIV (EXAR CORP) 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT73L03AIV |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP120 |
| 封裝： | 14 X 20 MM, TQFP-120 |
| 文件頁數： | 26/62頁 |
| 文件大?。?/td> | 494K |
| 代理商： | XRT73L03AIV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
XRT73L03A
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 2.0.4
24
SYSTEM DESCRIPTION
A functional block diagram of the XRT73L03A E3/
DS3/STS-1 Transceiver IC is presented in Figure 13.
The XRT73L03A contains three separate channels
with three distinct sections:
The Transmit Section - Channels 0, 1 and 2
The Receive Section - Channels 0, 1 and 2
The Microprocessor Serial Interface Section
THE TRANSMIT SECTION - CHANNELS 0, 1 AND 2
The Transmit Section, within each Channel, accepts
TTL/CMOS level signals from the Terminal Equip-
ment in either a Single-Rail or Dual-Rail format. The
Transmit Section then takes this data and does the
following:
Encode this data into the B3ZS format if the DS3 or
SONET STS-1 Modes has been selected or into
the HDB3 format if the E3 Mode has been selected.
Convert the CMOS level B3ZS or HDB3 encoded
data into pulses with shapes that are compliant with
the various industry standard pulse template
requirements.
Drive these pulses onto the line via the TTIP_(n)
and TRing_(n) output pins across a 1:1 Trans-
former.
N
OTE
:
The Transmit Section drives a "1" (or a Mark) onto
the line by driving either a positive or negative polarity pulse
across the 1:1 Transformer within a given bit period. The
Transmit Section drives a "0" (or a Space) onto the line by
driving no pulse onto the line.
THE RECEIVE SECTION - CHANNELS 0, 1 AND 2
The Receive Section, within each Channel, receives
a bipolar signal from the line via the RTIP and RRing
signals through a 1:1 Transformer or 0.01μF Capaci-
tor.
The recovered clock and data outputs to the Local
Terminal Equipment in the form of CMOS level sig-
nals via the RPOS_(n), RNEG_(n) and RxClk_(n)
output pins.
THE MICROPROCESSOR SERIAL INTERFACE
The XRT73L03A can be configured to operate in ei-
ther the Hardware Mode or the HOST Mode.
The XRT73L03A contains three identical channels.
The Microprocessor Interface Inputs are common to
all channels. The descriptions that follow refer to
Channel(n) where (n) represents channel 0, 1 or 2.
a. Operating in the Hardware Mode
When the XRT73L03A is operating in the Hardware
Mode, then the following is true:
1.
The Microprocessor Serial Interface block is dis-
abled.
2.
The XRT73L03A is configured via input pin set-
tings.
The XRT73L03A can be configured to operate in the
Hardware Mode by tying the HOST/(HW) input pin to
GND.
Each of the pins associated with the Microprocessor
Serial Interface takes on their alternative role as de-
fined inTable 1.
T
ABLE
1: R
OLE
OF
M
ICROPROCESSOR
S
ERIAL
I
NTERFACE
PINS
WHEN
THE
XRT73L03A
IS
OPERATING
IN
THE
H
ARDWARE
M
ODE
When the XRT73L03A is operating in the Hardware
Mode, all of the remaining input pins become active.
b. Operating in the HOST Mode
The XRT73L03A can be configured to operate in the
HOST Mode by tying the HOST/(HW) input pin to
VDD.
When the XRT73L03A is operating in the HOST
Mode, then the following is true.
1.
The Microprocessor Serial Interface block is
enabled. Writing the appropriate data into the
on-chip Command Registers makes many config-
uration selections.
2.
All of the following input pins are disabled and
should be connected to ground:
Pins 8, 9 & 35 - TxLEV_(n)
Pins 6, 7 & 36 - TAOS_(n)
Pin 74, 82 & 100 - REQEN_(n)
Pin 68, 76 & 88 - LLB_(n)
Pin 92 & 102 - E3_(n)
Pin 65, 95 & 101 - STS1/DS3_(n)
In HOST Mode Operation, the TxOFF_(n) input pins
can be used to turn on or turn off the Transmit Output
Drivers within all Channels concurrently. The intent
behind this feature is to permit a system designed for
P
IN
#
P
IN
N
AME
F
UNCTION
,
WHILE
IN
HARDWARE
MODE
61
CS/(ENDECDIS)
ENDECDIS
62
SClk/(RxOFF_1)
RxOFF_1
63
SDI/(RxOFF_0)
RxOFF_0
64
SDO/(E3_0)
E3_0
96
REGR/(RxClkINV)
RxClkINV
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L03B | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L03BIV | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L04A | 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L04AIV | 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L04B | 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73L03B | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L03BES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73L03BIV | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73L03BIV-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73L03IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 LINE INTERFCE UNIT |
發布緊急采購，3分鐘左右您將得到回復。