參數資料
| 型號： | XRT59L921IB |
| 廠商： | Exar Corporation |
| 文件頁數： | 20/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E1 21CH 316STBGA |
| 標準包裝： | 60 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 21/21 |
| 規(guī)程： | E1 |
| 電源電壓： | 3.13 V ~ 3.46 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 316-LBGA |
| 供應商設備封裝： | 316-STBGA（21x21） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
XRT59L921
25
REV. 1.2.1
TWENTY-ONE CHANNEL E1 LINE INTERFACE UNIT
indicator. In particular, the XRT59L921 will declare a LOS, between 10 and 255 UI (or E1 bit-periods) after the
actual time the LOS condition occurred. Further, the XRT59L921 will clear the LOS indicator within 10 to 255
UI after restoration of the incoming line signal. Figure 14 illustrates the LOS Declaration and Clearance
behavior, in response to first, the Loss of Signal event and then afterwards, the restoration of the signal.
2.6
LOS Mute Description
The LOSMute feature is included in the XRT59L921 such that when the input signal to a receiver is too low or
is lost. The LOS_n pin will toggle "High" and at the same time the RPOS_n and RNEG_n outputs are muted to
a "Zero" state to prevent output data chattering.
2.7
The Receive Output Interface block
The purpose of the Receive Output Interface block is to interface directly with the Receiving Terminal
Equipment. The Receive Output Interface block outputs the data (which has been recovered from the incoming
line signal) to the Receive Terminal Equipment via the RxPOS_n and RxNEG_n output pins.
If the Receive Sections of the XRT59L921 has received a Positive-Polarity pulse, via the RTIP_n and RRing_n
input pins, then the Receive Output Interface will output a pulse via the RxPOS_n output pins.
Similarly, if the Receive Sections of the XRT59L921 has received a Negative-Polarity pulse, via the RTIP_n
and RRing_n input pins, then the Receive Output Interface will output a pulse via the RxNEG_n output pins.
NOTE: The Receive Output Interface block does not supply a recovered clock. This device is intended to be used in those
applications, where the Clock Recovery circuit is realized in an ASIC solution.
3.0 SHUTTING OFF THE TRANSMITTER
Each channel (within the XRT59L921) permits the user to shut off the Transmit Driver within their respective
Transmit Section. This feature can come in handy for system redundancy design considerations or during
diagnostic testing. The user can activate this feature by connecting the TxClk_n input pin to a logic “0” (e.g.,
GND) and continue to apply data via the TxPOS_n and TxNEG_n input pins.
FIGURE 14. THE BEHAVIOR OF THE LOS OUTPUT INDICATOR, IN RESPONSE TO THE LOSS OF SIGNAL, AND THE
RESTORATION OF THE SIGNAL
LOS Output Pin
0 UI
0UI
10 UI
Actual Occurrence
of LOS Condition
Line Signal
is Restored
255 UI
RxIN
G.775 Compliance
Time Range for
LOS Declaration
Time Range for
LOS Clearance
相關PDF資料 |
PDF描述 |
|---|---|
| XRT72L50IQ-F | IC FRAMER DS3/E3 SGL 100QFP |
| XRT72L52IQTR-F | IC FRAMER DS3/E3 2CH 160QFP |
| XRT72L53IB-F | IC FRAMER DS3/E3 3CH 272PBGA |
| XRT72L54IB | IC FRAMER DS3/E3 4CH 272PBGA |
| XRT72L71IQ | IC FRAMER DS3 ATM UNI 160PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT-600 | 制造商:Pro-Signal 功能描述:PATCH LEAD CAT5E X-OVER 0.5M 制造商:PRO SIGNAL 功能描述:PATCH LEAD, CAT5E, X-OVER, 0.5M 制造商:pro-power 功能描述:PATCH LEAD, CAT5E, X-OVER, 0.5M; Connector Type A:RJ45 Plug; Connector Type B:RJ45 Plug; Cable Length - Imperial:19.69"; Cable Length - Metric:500mm; Jacket Colour:Grey; Cable Assembly Type:Network; Cable Length:0.5m; Colour:Grey; |
| XR-T6000CN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT-601 | 制造商:Pro-Signal 功能描述:PATCH LEAD CAT5E X-OVER 1M 制造商:pro-power 功能描述:PATCH LEAD, CAT5E, X-OVER, 1M 制造商:PRIVATE LABEL 功能描述:PATCH LEAD, CAT5E, X-OVER, 1M, Connector Type A:RJ45 Plug, Connector Type B:RJ45 |
| XR-T6010CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT-602 | 制造商:Pro-Signal 功能描述:PATCH LEAD CAT5E X-OVER 2M 制造商:PRO SIGNAL 功能描述:PATCH LEAD, CAT5E, X-OVER, 2M |
發(fā)布緊急采購，3分鐘左右您將得到回復。