- 您現在的位置：買賣IC網 > PDF目錄10786 > XRT5894IV-F (Exar Corporation)IC LIU E1 QUAD 64TQFP PDF資料下載
參數資料
| 型號： | XRT5894IV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 3/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E1 QUAD 64TQFP |
| 標準包裝： | 160 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規程： | E1 |
| 電源電壓： | 3.14 V ~ 3.47 V，4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1480 XRT5894IV-F-ND |
XRT5894
11
Rev. 1.10
SYSTEM DESCRIPTION
This device is a four channel E1 transceiver that provides
an electrical interface for 2.048Mbps applications. Its
unique architecture includes four receiver circuits that
convert ITU G.703 compliant bipolar signals to TTL
compatible logic levels. Each receiver includes a LOS
(Loss of Signal) detection circuit that may be configured
for either a fixed or a user-programmable LOS response
time delay. Similarly, in the transmit direction, four
transmitters convert TTL compatible logic levels to G.703
compatible bipolar signals. Each transmitter may be
operated either with RZ, or NRZ data types. In NRZ mode
a transmit clock is required as well. The following
description applies to any of the four receivers or
transmitters contained in the XRT5894. Therefore, the
suffix numbers for a particular channel are deleted for
simplicity. i.e. “RTIP” applies to RTIP1 through RTIP4.
Receiver Operation
A bipolar signal is transformer-coupled to the receiver
differential inputs (RTIP and RRING). The receiver is able
to tolerate up to 12dB of line loss measured at 1.024MHz.
It contains slicing circuitry that automatically samples the
incoming data at a fixed percentage (50% nominal) of the
peak signal amplitude. A precision peak detector
maintains the slicing level accuracy. The TTL compatible
receiver output data rails appear at the RXPOS and
RXNEG pins. The pulse width of this data; which is in RZ
format, is a function of the amount of the cable loss
present.
Receiver Loss Of Signal Detection (LOS)
Absence of signal at any receiver input is detected by the
loss of signal (LOS) circuit. One LOS detection circuitry is
provisioned for each receiver. The LOS signal is asserted
(LOS=1) when a LOS condition is detected and is cleared
(LOS=0) when a valid input signal is restored.
Two modes of LOS circuit operation are supported.
These distinct modes are called “automatic” and
“user-programmable”. When LOSSEL (pin 25) is set to
logic “1”, the automatic mode is selected. In this mode the
LOS condition will be declared and cleared in full
compliance with ITU G.775 specification. When LOSSEL
is connected to logic “0”, the user-programmable delay
mode is enabled. In this mode the user has the option of
extending the delay of LOS declaration and clearing
specified in the ITU G.775. This is done by providing a
user-supplied clock to LOSCNT (pin 45). The “user
programmable mode” is provisioned to allow systems
designers to comply with older versions of LOS
specifications in legacy systems. It needs to be stressed
that the delay for declaration and clearing of the LOS
condition will never be less than the range specified in the
G.775 specification (10-255 pulse intervals).
The LOS detection/clearing circuitry of the XRT5894 in
“automatic” mode will detect LOS when the incoming
signal has “no transitions” i.e. when the signal level is less
than or equal to a signal level AD dB below nominal signal
level, for N consecutive pulse intervals, where 10<N<255.
The value of AD can vary between 10dB to 32dB
depending on the ones density of the incoming signal
assuming the received data has minimum permissible
ones density. Furthermore LOS detect is cleared when
the incoming signal has “transitions,” i.e. when the signal
level is greater than or equal to a signal level of AC dB
below nominal, for N consecutive pulse intervals, where
10<N<255. The value of AC can vary between 9dB to
31dB depending on the ones density of the incoming
signal assuming the received data has minimum
permissible ones density. Each pulse interval is 488ns at
E1 rates. The absolute value of AC is always smaller than
AD by at least 1dB.
The LOS detection/clearing criteria described above is
fully compliant with G.775 LOS specification. In the “user
programmable” mode the user has the option of
extending the declaration and clearing delay (10<N<255)
by an amount which is equal to 2048 x T. T is the time
period of the clock supplied to LOSCNT (pin 45) by the
user.
Nominal signal level is defined as 2.37V peak measured
between RTIP or RRING and ground. (This voltage will
be present in 75W applications using a 1:2 CT ratio input
transformer terminated in 300W with the center tap
grounded with 0dB of cable and a 2.37V peak amplitude
transmit pulse at the cable input.)
Transmitters
This device contains four identical ITU G.703 compliant
transmitters. The output stage of each transmitter is a
differential voltage driver. External resistors need to be
connected to the primary of output transformer. This is
necessary to maintain an accurate source impedance
相關PDF資料 |
PDF描述 |
|---|---|
| VI-JTW-MY-S | CONVERTER MOD DC/DC 5.5V 50W |
| AD5582YRVZ-REEL | IC DAC 12BIT PARALLEL IN 48TSSOP |
| VI-BNV-MX-F1 | CONVERTER MOD DC/DC 5.8V 75W |
| AD5316BRUZ-REEL | IC DAC 10BIT QUAD W/BUFF 16TSSOP |
| VI-JTV-MY-S | CONVERTER MOD DC/DC 5.8V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT5894IVTR-F | 功能描述:接口 - 專用 QuadE1 LIU3.3/5.5V RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| XRT5897 | 制造商:EXAR 制造商全稱:EXAR 功能描述:Seven-Channel E1 Line Interface |
| XRT5897ES | 功能描述:外圍驅動器與原件 - PCI 7 CH E1 AFE RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT5897IV | 功能描述:外圍驅動器與原件 - PCI 7CH E1 LIU RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT5897IV-F | 功能描述:外圍驅動器與原件 - PCI 7 Ch.E1LIU3.3/5.5V RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。