- 您現在的位置：買賣IC網 > PDF目錄376460 > XRT5894ES (Exar Corporation) () PDF資料下載
參數資料
| 型號： | XRT5894ES |
| 廠商： | Exar Corporation |
| 英文描述： | () |
| 中文描述： | （） |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 289K |
| 代理商： | XRT5894ES |
XRT5894ES
2
Rev. 1.00
Overview
This unit is a 4.5 by 4.5 inch circuit board that simplifies the evaluation of the XRT5894 four
channel, 3.3/5.0 V, E1, line interface unit integrated circuit. Its features include use of a 4-layer
circuit board with surface mount technology to minimize noise, provisions for an equipment-
side loopback that simplifies testing, and options for operation either with or without an external
LOS (Loss of Signal) output delay clock. Figures 1, 2 and 3 and Table 2 show the demo board
transmit pulse waveform, component layout, circuit diagram, and parts list respectively.
Power Requirements
A well-regulated source of +3.3 or +5.0V
±
5%V must be applied to the board at the red (positive)
and black (negative) banana jacks.
Equipment-side Digital Input and Output Connections
The component layout given in Figure 2 shows the location of the equipment-side digital
receiver input and transmitter output connections for each of the four independent transmitters
and receivers. For versatility, the I/O connections on each channel may be made to either a
set of 6 test points, or to a 10-pin header that will accept a ribbon cable connector. The tests
points are convenient for lab evaluations and signal monitoring, while the ribbon cable
connections offer a method of integrating the XRT5894 board into a larger system.
Table 1 shows the I/O connections for Channel 1. It also applies to the other channels if the
digit indicating the Signal and Test Point name is changed to the appropriate channel (e.g. “1”
in RXPOS1, etc.). Note the pin 1 locations for the ribbon cable connectors that are shown on
the component layout. Pin 1 is at top left for Channels 1 and 4, and at bottom right for Channels
2 and 3. The schematic diagram given in Figure 3 may be used to verify these connections.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT5894 | Four-Channel E1 Line Interface (3.3V or 5.0V)(四通道E1 3.3V線接口單元) |
| XRT5897ES | () |
| XRT5897 | Seven-Channel E1 Line Interface (3.3V or 5.0V)(七通道E1 3.3V線接口單元) |
| XRT5997 | Seven-Channel E1 Line Interface Unit(7通道 E1線接口單元) |
| XRT59L91 | Single-Chip E1 Line Interface Unit(單片E1 線接口單元) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT5894IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:Four-Channel E1 Line Interface (3.3V or 5.0V) |
| XRT5894IV-F | 功能描述:外圍驅動器與原件 - PCI 3.3V or 5V 4-ch E1 temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT5894IVTR-F | 功能描述:接口 - 專用 QuadE1 LIU3.3/5.5V RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| XRT5897 | 制造商:EXAR 制造商全稱:EXAR 功能描述:Seven-Channel E1 Line Interface |
| XRT5897ES | 功能描述:外圍驅動器與原件 - PCI 7 CH E1 AFE RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。