- 您現在的位置：買賣IC網 > PDF目錄3762 > XR88C92CJTR-F (Exar Corporation)IC UART FIFO DUAL 44PLCC PDF資料下載
參數資料
| 型號： | XR88C92CJTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO DUAL 44PLCC |
| 標準包裝： | 500 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
XR88C92/192
19
Rev. 1.33
0 1 1 0 = Start Break. Forces the transmitter output to
go low and stay low. If transmitter is empty
the start of the break condition will be de-
layed up to two bit times. If transmitter is
active, all the characters in the FIFO are
transmitted before break signal is sent.
Transmitter must to be enabled for this com-
mand to work.
0 1 1 1 = Stop Break. Transmit output will go high
within two bit times.
1 0 0 0 = Set -RTS output to low (assertion).
1 0 0 1 = Reset -RTS output to high (negation).
1 01 0 = Set Timeout Mode On. The receiver in this
channel will restart the C/T as each receive
character is transferred from the shift regis-
ter to the receive FIFO. The C/T is placed in
the counter mode, the START/STOP counter
commands are disabled, the counter is
stopped, and the Counter Ready Bit, ISR Bit-
3 is reset. (See also Watchdog timer de-
scription)
1 0 1 1 = Set MR pointer to MR0.
1 1 0 0 = Disable Timeout Mode. This command re-
turns control of the C/T to the regular Start/
Stop counter commands. It does not stop the
counter or clear any pending interrupts. After
disabling the timeout mode, a “Stop Counter”
command should be issued to force a reset
of the ISR Bit-3.
1 1 0 1 = Not used.
1 1 1 0 = Enable Power Down Mode. In this mode, the
DUART oscillator is stopped and all functions
requiring this clock are suspended. The
execution of commands other than disable
power down mode (1111) requires a XTAL1.
While in the power down mode, do not issue
any commands to the CRA or CRB except the
disable power down mode command. The
contents of all registers will be saved while in
this mode. It is recommended that the trans-
mitter and receiver be disabled prior to plac-
ing the DUART into power down mode. This
command is in CRA only.
1 1 1 1 = Disable Power Down Mode. This command
restarts the oscillator. After invoking this
command, wait for the oscillator to start up
before writing further commands to the CR A/
B. For maximum power reduction all input
pins should be at GND or VCC. This com-
mand is in CRA only.
RECEIVE BUFFER (RXA, RXB)
The receive buffer consists of a 8-characters deep
FIFO in XR88C92 and 16-characters deep FIFO in
XR88C192. The received characters are transferred
from the shift register one at a time to the FIFO and are
stored there until read by the CPU or flushed by a reset
receiver command.
TRANSMIT BUFFER (TXA, TXB)
The transmit buffer consists of a 8-characters deep
FIFO in XR88C92 and 16-characters deep FIFO in
XR88C192. Once loaded in the FIFO, the characters
are transferred to the transmit shift register one at a time
and transmitted unless the transmitter is disabled.
INPUT PORT CHANGE REGISTER (IPCR)
This is a read-only register which gives the state and the
change-of-state information of the multi-purpose inputs
IP0, IP1, IP2 and IP3.
IPCR Bits 3-0: Levels of IP3 - IP0.
These show the current state of IP3, IP2, IP1 and IP0
respectively.
0 = Low
1 = High
IPCR Bits 7-4: Transitions of IP3 - IP0.
These indicate if there has been a change of state in IP3,
IP2, IP1 and IP0 respectively. They are cleared when
the register is read by the CPU.
0 = No
1 = Yes
AUXILIARY CONTROL REGISTER (ACR)
ACR Bits 3-0:
This field selects which bits of the input port change
register (IPCR) cause the interrupt status register (ISR)
bit-7 to be set. For example, if bit-0 = 1, then a change
of state in IP0 will set ISR bit-7. If bit-0 and bit-2 are both
'1', then whenever IP0 or IP2 changes state, ISR bit-7
will be set.
0 = Disabled (default)
1 = Enabled
ACR Bits 6-4:
Counter/Timer Mode and Clock Source. These bits
should not be altered while the C/T is in use. Prior to
changing these bits, the C/T must be stopped if in
counter mode. If the C/T is in timer mode, its output must
be disabled and its interrupt must be masked. The
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C452CJ68TR-F | IC UART W/PAR PORT DUAL 68PLCC |
| ST16C552CJ68TR-F | IC UART FIFO 16B DUAL 68PLCC |
| XR68C681CJTR-F | IC UART CMOS DUAL 44PLCC |
| ST16C2550CJ44TR-F | IC UART FIFO 16B DUAL 44PLCC |
| XR16V2750IMTR-F | IC UART FIFO 64B DUAL 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR88C92CP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C92CV | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C92CV-0A-EVB | 功能描述:界面開發工具 Supports 88C92 44 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR88C92CV-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C92CVTR-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。