REV. 1.1.1 HIGH PERFORMANCE DUART WITH 64-BYTE FIFO INTA (IRQ#) 22 30 D6 O When 16/68# pin is HIGH for Intel bus interface," />
參數資料
型號: XR68M752IL32TR-F
廠商: Exar Corporation
文件頁數: 45/54頁
文件大?。?/td> 0K
描述: IC UART FIFO 64B DUAL 32QFN
標準包裝: 3,000
特點: *
通道數: 2,DUART
FIFO's: 64 字節
規程: RS232,RS422,RS485
電源電壓: 1.62 V ~ 3.63 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-QFN 裸露焊盤(5x5)
包裝: 帶卷 (TR)
XR16M752/XR68M752
5
REV. 1.1.1
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
INTA
(IRQ#)
22
30
D6
O
When 16/68# pin is HIGH for Intel bus interface, this out-
put becomes channel A interrupt output. The output state
is defined by the user through the software setting of
MCR[3]. INTA is set to the active mode and OP2A# out-
put LOW when MCR[3] is set to a logic 1. INTA is set to
the three state mode and OP2A# to HIGH when MCR[3]
is set to a logic 0. See MCR[3].
When 16/68# pin is LOW for Motorola bus interface, this
output becomes device interrupt output (active low, open
drain). An external pull-up resistor is required for proper
operation.
INTB
(NC)
21
29
D7
O
When 16/68# pin is HIGH for Intel bus interface, this out-
put becomes channel B interrupt output. The output state
is defined by the user through the software setting of
MCR[3]. INTB is set to the active mode and OP2A# out-
put to LOW when MCR[3] is set to a logic 1. INTA is set to
the three state mode and OP2A# to HIGH when MCR[3]
is set to a logic 0. See MCR[3].
When 16/68# pin is LOW for Motorola bus interface, this
output is not used.
TXRDYA#
-
43
C4
O
UART channel A Transmitter Ready (active low). The
output provides the TX FIFO/THR status for transmit
channel A. See
Table 3. If it is not used, leave it uncon-
nected.
RXRDYA#
-
31
E5
O
UART channel A Receiver Ready (active low). This out-
put provides the RX FIFO/RHR status for receive channel
A. See
Table 3. If it is not used, leave it unconnected.
TXRDYB#
-
6
D4
O
UART channel B Transmitter Ready (active low). The
output provides the TX FIFO/THR status for transmit
channel B. See
Table 4. If it is not used, leave it uncon-
nected.
RXRDYB#
-
18
F4
O
UART channel B Receiver Ready (active low). This out-
put provides the RX FIFO/RHR status for receive channel
B. See
Table 3. If it is not used, leave it unconnected.
MODEM OR SERIAL I/O INTERFACE
TXA
5
7
D3
O
UART channel A Transmit Data or infrared encoder data.
Standard transmit and receive interface is enabled when
MCR[6] = 0. In this mode, the TX signal will be HIGH dur-
ing reset or idle (no data). Infrared IrDA transmit and
receive interface is enabled when MCR[6] = 1. In the
Infrared mode, the inactive state (no data) for the Infrared
encoder/decoder interface is LOW. If it is not used, leave
it unconnected.
Pin Description
NAME
32-QFN
PIN #
48-TQFP
PIN #
49-STBGA
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
ATMEGA168-15AT MCU AVR 16K FLASH 15MHZ 32-TQFP
ST16C450CQ48TR-F IC UART SINGLE 48TQFP
ST16C450IJ44TR-F IC UART SINGLE 44PLCC
XR16M770IL24-F IC UART FIFO 64B 24QFN
XR16M680IL32-F IC UART FIFO 32B 32QFN
相關代理商/技術參數
參數描述
XR68M752IM-0B-EB 功能描述:界面開發工具 Support XR68M752 48L TQFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR68M752IM48 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR68M752IM48-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR68M752IM48TR-F 制造商:Exar Corporation 功能描述:XR68M752 Series 16 Mbps High Performance DUART With 64-Byte FIFO - TQFP-48
XR7090AA-BC-0001 制造商:CREE 制造商全稱:Cree, Inc 功能描述:XLamp㈢ XR LED Binning and Labeling