- 您現在的位置：買賣IC網 > PDF目錄11832 > XR68C192IV-F (Exar Corporation)IC UART FIFI DUAL 44PLCC PDF資料下載
參數資料
| 型號： | XR68C192IV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 5/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFI DUAL 44PLCC |
| 標準包裝： | 160 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
| 其它名稱： | XR68C192IV-F-ND |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
XR68C92/192
13
Rev. 1.33
dress 0x7) can be from 0x0001 through 0xFFFF and can
be changed at any time. At power-up and after reset, the
C/T operates in counter mode.
COUNTER MODE
In counter mode, the CPU can start and stop the C/T.
This mode allows the C/T to function as a system
stopwatch or a real-time single interrupt generator. In
this mode, the C/T counts down from the pre-load
value using the programmed counter clock source.
When a read at the start counter command register
(address 0xE) is performed, the counter is initialized to
the pre-load value and begins a countdown sequence.
When the counter counts from 0x0001 to 0x0000
(terminal count), the C/T-ready bit in the interrupt
status register (ISR Bit-3) is set.
3
Users can program the counter to generate an inter-
rupt request for this condition on the -INT output by
unmasking the bit-3 in the Interrupt Mask Register
(IMR, address 0x5). After 0x0000 the count becomes
0xFFFF, and the counter continues counting down
from there. If the CPU changes the pre-load value, the
counter will not recognize the new value until it receives
the next start counter command (and is reinitialized).
When a read at the stop counter command register
(address 0xF) is performed, the counter stops the
countdown sequence and clears ISR Bit-3. The count
value should only be read while the counter is stopped
because only one of the count registers (either CUR, at
address 0x6 or CLR, at address 0x7) can be read at a
time. If the counter is running, a decrement of CLR that
requires a borrow from the CUR could take place
between the two register reads. Figure 2 shows the
C/T output in the counter mode. OP3 can be pro-
grammed to show the C/T output.
In addition to the watch dog timer described above, the
C/T can be used for receive timeout function (see
description under CRA, CRB in the registers section
also). The C/T is more accurate and the timeout period
is programmable unlike the watchdog timer. However,
only one channel can use the C/T for receive timeout
at any given time. The C/T timeout mode uses the
received data stream to start the counter. Each time a
character is shifted from the receive shift register to the
receive FIFO, the C/T is reloaded with the pro-
grammed value in CTPU and CTPL and it restarts on
the next C/T clock. If a new character is not received
before the C/T reaches terminal count (= 0x0000), a
counter ready interrupt (ISR bit-3) is generated. The
user can appropriately program the CTPU and CTPL
for the desired timeout period. Typically this is slightly
more than one character time. Note that if C/T is used
for receiver timeout, a counter ready interrupt is gener-
ated whereas if the watchdog timer is used, a receiver
ready interrupt is generated.
TIMER MODE
In the timer mode, the C/T runs continuously once the
start command is issued (by reading the start C/T
PRELOAD
VALUE
TERMINAL
COUNT
C/T OUTPUT IN
COUNTER MODE
C/T OUTPUT IN
TIMER MODE
PRELOAD
VALUE
TERMINAL
COUNT
PRELOAD
VALUE
TERMINAL
COUNT
PRELOAD
VALUE
PRELOAD
VALUE
TERMINAL
COUNT
TERMINAL
COUNT
TERMINAL
COUNT
PRELOAD
VALUE
PRELOAD
VALUE
START C/T COMMAND
ISSUED
PRELOAD
VALUE
TERMINAL
COUNT
Figure 2: C/T output in Timer and Counter modes.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M554IJ68-F | IC UART FIFO 16B QUAD 68PLCC |
| VI-2WM-IY | CONVERTER MOD DC/DC 10V 50W |
| XR82C684CJTR/44-F | IC UART CMOS QUAD 44PLCC |
| ST16C454CJ68-F | IC UART QUAD 68PLCC |
| ST16C454IJ68-F | IC UART QUAD 68PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR68C681 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS Dual Channel UART (DUART) |
| XR68C681CJ | 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS Dual Channel UART (DUART) |
| XR68C681CJ44 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XR68C681CJ-F | 功能描述:UART 接口集成電路 0.5V-2V UART temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR68C681CJ-F | 制造商:Exar Corporation 功能描述:IC UART 2CH 68C681 PLCC44 |
發布緊急采購，3分鐘左右您將得到回復。