- 您現在的位置：買賣IC網 > PDF目錄2120 > XR2211ACDTR-F (Exar Corporation)IC FSK DEMOD/TONE DECOD 14SOIC PDF資料下載
參數資料
| 型號： | XR2211ACDTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FSK DEMOD/TONE DECOD 14SOIC |
| 標準包裝： | 2,500 |
| 功能： | FSK 解調器，音頻解碼器 |
| 電源電壓： | 4.5 V ~ 20 V |
| 電流 - 電源： | 5mA |
| 功率（瓦特）： | 900mW |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
| 包括： | 載波檢測 |
| 其它名稱： | XR2211ACDTR-F-ND |
XR-2211A
16
Rev. 1.04
Design Instructions:
The circuit of
Figure 12 can be optimized for any tone detection application by the choice of the 5 key circuit components:
R0, R1, C0, C1 and CD. For a given input, the tone frequency, fS, these parameters are calculated as follows:
(All resistance in
W’s, all frequency in Hz and all capacitance in farads, unless otherwise specified)
a) Choose value of timing resistor R0 to be in the range of 10KW to 50KW. This choice is dictated by the max./min.
current that the internal voltage reference can deliver. The recommended value is R0 = 20KW. The final value of R0
is normally fine-tuned with the series potentiometer, RX.
b) Calculate value of C0 from design equation (1) or from Figure 7 fS = fO:
C
O +
1
R
0fs
c)
Calculate R1 to set the bandwidth +Df (See design equation 5):
R
1
+
R
0f02
Df
Note: The total detection bandwidth covers the frequency range of fO +Df
d) Calculate value of C1 for a given loop damping factor:
Normally,
j = 0.5 is recommended.
C
1
+
1250
C
0
R
1
j2
Increasing C1 improves the out-of-band signal rejection, but increases the PLL capture time.
e) Calculate value of the filter capacitor CD . To avoid chatter at the logic output, with RD = 470KW, CD must be:
C
D
§ 16
Df
Cin
mF
Increasing CD slows down the logic output response time.
Design Examples:
Tone detector with a detection band of + 100Hz:
a) Choose value of timing resistor R0 to be in the range of 10KW to 50KW. This choice is dictated by the max./min.
current that the internal voltage reference can deliver. The recommended value is R0 = 20 KW. The final value of R0
is normally fine-tuned with the series potentiometer, RX.
b) Calculate value of C0 from design equation (1) or from Figure 6 fS = fO:
C
0
+ 1
R
0fS
+
1
20, 0001, 000
+ 50nF
相關PDF資料 |
PDF描述 |
|---|---|
| XRD64L43AIV-F | IC ADC 10B PAR 40MSPS DL 64LQFP |
| XRD8775AIU-F | IC ADC 8BIT PAR 20MSPS 20SSOP |
| XRD8785AIDTR-F | IC ADC 8BIT 20MSPS 24SOIC |
| XRD8799AIQ | IC ADC 10BIT 2MSPS 44PQFP |
| XRD87L75AIUTR | IC ADC 8BIT 10MSPS 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR2211ACP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-FSK DEMODULATOR |
| XR-2211ACP | 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK Demodulator/ Tone Decoder |
| XR2211ACP-F | 功能描述:VCO振蕩器 4.5V-20V 5mA temp 0C to 70C RoHS:否 制造商:Exar 封裝 / 箱體:SOIC-14 頻率:300 kHz 負載電容: 封裝:Reel 電源電壓:4.5 V to 20 V 尺寸:4 mm W x 8.75 mm L x 1.75 mm H 最小工作溫度:0 C 最大工作溫度:+ 70 C |
| XR2211ACP-F | 制造商:Exar Corporation 功能描述:IC DEMODULATOR/DECODER FSK 2211 |
| XR2211ACP-F | 制造商:Exar Corporation 功能描述:FSK Demodulator/ Tone Decoder IC |
發布緊急采購，3分鐘左右您將得到回復。