參數資料
型號： XR19L222IL64-F
廠商： Exar Corporation
文件頁數： 51/53頁
文件大?。?/td> 0K
描述： IC UART/TXRX RS232 64QFN
標準包裝： 260
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232
電源電壓： 3.3 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤
供應商設備封裝： 64-QFN（9x9）
包裝： 托盤
XR19L222
7
REV. 1.0.1
TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
1.0
PRODUCT DESCRIPTION
The XR19L222 consists of a two-channel UART and RS-232 transceivers. It operates from a single +3V to
5.5V supply with data rates up to 1Mbps, while meeting all EIA RS-232F specifications. Its feature set is fully
compatible to the industry standard 16C550. Unlike the 16C550, most of the modem signals are not CMOS/
TTL level, but conform to EIA/TIA 232 or RS-232 voltage levels. The only two signals that are CMOS/TTL level
are the TXB and RXB signals. They can be used with an external IR or RS-422 transceiver when their
corresponding RS-232 signals, TXDB and RXDB, are not used. The configuration register set is 16550 UART
compatible for control, status and data transfer. Also, the L222 has 64-bytes of transmit and receive FIFOs,
automatic RTS/CTS hardware flow control, automatic Xon/Xoff and special character software flow control,
transmit and receive FIFO trigger levels, and a programmable fractional baud rate generator with a prescaler
of divide by 1 or 4. Additionally, the L222 includes the ACP pin which the user can shut down the charge pump
for the RS-232 drivers. In the UART portion, the Power-Save feature isolates the databus interface to further
reduce power consumption in the Sleep mode. The L222 is fabricated using an advanced CMOS process.
Enhanced Features
The L222 UART provides a solution that supports 64 bytes of transmit and receive FIFO. Increased
performance is realized in the L222 by the transmit and receive FIFOs, FIFO trigger level controls and
automatic flow control mechanism. This allows the external processor to handle more networking tasks within
a given time. This increases the service interval giving the external CPU additional time for other applications
and reducing the overall UART interrupt servicing time. In addition, the L222 provides the ACP and Power-
Save modes that drastically reduces the power consumption when the device is not used. The combination of
the above greatly reduces the CPU’s bandwidth requirement, increases performance, and reduces power
consumption.
Intel or Motorola Data Bus Interface
The L222 provides a host interface that supports Intel or Motorola microprocessor (CPU) data bus interface.
The Intel bus compatible interface allows direct interconnect to Intel compatible type of CPUs using IOR#,
IOW# and CS# inputs for data bus operation. The Motorola bus compatible interface instead uses the R/W#
and CS# signals for data bus transactions. See pin description section for details on all the control signals. The
Intel and Motorola bus interface selection is made through the pin, I/M#.
Data Rate
The L222 is capable of operation up to 1 Mbps data rate. The UART section can operate at much higher
speeds, but the speed of the RS-232 transceiver is limited to 1 Mbps. The device can operate either with a
crystal on pins XTAL1 and XTAL2, or external clock source on XTAL1 pin.
Internal Enhanced Register Sets
The L222 UART has a set of enhanced registers providing control and monitoring functions. Interrupt enable/
disable and status, FIFO enable/disable, selectable TX and RX FIFO trigger levels, automatic hardware/
software flow control enable/disable, programmable baud rates, modem interface controls and status, sleep
mode and infrared mode are all standard features. Following a power on reset or an external reset (and
operating in 16 or Intel Mode), the registers defaults to the reset condition and is compatible with the 16C550.
RS-232 Interface
The L222 includes RS-232 drivers/receivers for the entire modem interface. This feature eliminates the need
for an external RS-232 transceiver. The charge pump provides output voltages of +5V and -5V for its drivers
over the 3.3V to 5.5V VCC supply voltage. The serial outputs TXD, RTS and DTR swing between -5V (inactive)
and 5V (active) RS-232 voltage levels. The serial inputs RXD, CTS, DSR, CD and RI are RS-232 receivers and
can take any voltage swing from -15V to +15V. The receivers are always active, even in Full Sleep and Power-
Save modes. The RS-232 drivers guarantee a data rate of 1 Mbps even when fully loaded with 3Kohm in
parallel with 1000pF load.
All RS-232 drivers and receivers are protected to ±15kV using the Human Body Model ground combination,
±8kV using IEC 61000-4-2 Contact Discharge, and ±15kV using IEC 61000-4-2 Air-Gap Discharge. For more
information, send an e-mail to uarttechsupport@exar.com.
相關PDF資料
PDF描述
XR19L400IL40-F IC UART/TXRX RS485 40QFN
XR19L402IL48-F IC UART/TXRX RS485 48QFN
XR20M1170IL24TR-F IC UART FIFO I2C/SPI 64B 24QFN
XR20M1172IG28-F IC UART FIFO I2C/SPI 64B 28TSSOP
XR20M1280IL40-F IC UART I2C/SPI 128 BYTE 40QFN
相關代理商/技術參數
參數描述
XR19L400 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
XR19L400_09 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
XR19L400IL40 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
XR19L400IL40-0B-EB 功能描述:界面開發工具 Supports L400 40 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR19L400IL40-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*