FIGURE 10. RECEIVER O
參數資料
型號： XR16V564IL-0A-EVB
廠商： Exar Corporation
文件頁數： 10/54頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16V564 48QFN
標準包裝： 1
系列： *
FIGURE 10. RECEIVER OPERATION IN FIFO AND AUTO RTS FLOW CONTROL MODE
Receive Data Shift
R egister (RSR)
R XFIFO 1
16X or 8X or 4X Clock
( DLD[5:4] )
Err
or
T
a
gs
(32
-se
ts
)
Er
ro
rT
ag
si
n
LS
R
b
its
4:
2
R eceive D ata Characters
Data Bit
Validation
Receive
Data FIFO
Receive
Data
Receive Data
Byte and Errors
RH R Interrupt (ISR bit-2) program m ed for
desired FIFO trigger level.
FIFO is Enabled by FCR bit-0=1
R TS# de-asserts when data fills above the flow
control trigger level to suspend rem ote transm itter.
Enable by EFR bit-6=1, M C R bit-1.
R TS# re-asserts when data falls below the flow
control trigger level to restart rem ote transm itter.
Enable by EFR bit-6=1, M CR bit-1.
32 bytes by 11-bit wide
FIFO
Trigger=16
D ata falls to
8
D ata fills to
24
Exam ple
: - R X FIFO trigger level selected at 16 bytes
(See N ote Below )
XR16V564/564D
18
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.4
2.11
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 11):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the RTS#
pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.12
Auto RTS Hysteresis
The V564 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the XR16C850, ST16C650A and ST16C550 family of UARTs. With the Auto RTS function enabled, an interrupt
is generated when the receive FIFO reaches the selected RX trigger level. The RTS# pin will not be forced
HIGH (RTS off) until the receive FIFO reaches one trigger level above the selected trigger level in the trigger
table (Table 12). The RTS# pin will return LOW after the RX FIFO is unloaded to one level below the selected
trigger level. Under the above described conditions, the V564 will continue to accept data until the receive
FIFO gets full. The Auto RTS function is initiated when the RTS# output pin is asserted LOW (RTS On).
TABLE 7: AUTO RTS (HARDWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
RTS# DE-ASSERTED (HIGH)
(CHARACTERS IN RX FIFO)
RTS# ASSERTED (LOW)
(CHARACTERS IN RX FIFO)
8
16
0
16
24
8
24
30
16
30
24
相關PDF資料
PDF描述
XC61CC2802MR-G IC SUPERVISOR 2.8V SOT23-3
RPP30-4824DW-1F CONV DC/DC 30W 18-75V +/-24VOUT
6588573-1 C/A, MT-RJ TO SC DUPLEX XG FI
M3CCK-1620K IDC CABLE - MKC16K/MC16F/MKC16K
LB2016T101K INDUCTOR WOUND 100UH 40MA 0806
相關代理商/技術參數
參數描述
XR16V564IL-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564IV 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16V564IV-0A-EVB 功能描述:UART 接口集成電路 Supports V564 64 ld LQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564IV80 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
XR16V564IV80-0A-EB 功能描述:UART 接口集成電路 Supports V564 80 ld LQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*