- 您現(xiàn)在的位置：買賣IC網 > PDF目錄16492 > XR16V564DIV-0A-EB (Exar Corporation)EVAL BOARD FOR XR16V564D 64LQFP PDF資料下載
參數資料
| 型號： | XR16V564DIV-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 24/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16V564D 64LQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
XR16V564/564D
30
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.4
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the -TXRDY and -RXRDY pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select (requires EFR bit-4 = 1)
(logic 0 = default, TX trigger level = 16)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 12 below shows the selections.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =8)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 12 shows the complete selections.
TABLE 12: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
BIT-7
BIT-6
BIT-5
BIT
-4
RECEIVE
TRIGGER
LEVEL
TRANSMIT
TRIGGER
LEVEL
0
1
0
1
0
1
0
1
0
1
0
1
8
16
24
30
16
8
24
30
FCR
相關PDF資料 |
PDF描述 |
|---|---|
| M3BBK-1618R | IDC CABLE - MSR16K/MC16M/MSR16K |
| CDRH2D14NP-1R5NC | INDUCTOR POWER 1.5UH 2A SMD |
| RPP30-2424SW-F | CONV DC/DC 30W 9-36VIN 24VOUT |
| XC61CN2202MR-G | IC SUPERVISOR 2.2V SOT23-3 |
| 6374039-8 | C/A 62.5/125, PLNM ZIP, SC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V564DIV-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V564DIVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564DIVTR-F |
| XR16V564IJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V564IJ-0A-EVB | 功能描述:UART 接口集成電路 Supports V564 68 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V564IJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。