NOTE
參數資料
型號： XR16V2751IM-F
廠商： Exar Corporation
文件頁數： 8/52頁
文件大?。?/td> 0K
描述： IC UART FIFO 64B DUAL 48TQFP
標準包裝： 250
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS485
電源電壓： 2.25 V ~ 3.6 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
XR16V2751
16
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO AND POWERSAVE FEATURE
REV. 1.0.1
NOTE: Table-B selected as Trigger Table for
2.13
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 10):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.14
Auto RTS Hysteresis
The V2751 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the XR16C850, ST16C650A and ST16C550 family of UARTs. With the Auto RTS function enabled, an interrupt
is generated when the receive FIFO reaches the programmed RX trigger level. The RTS# pin will not be forced
HIGH (RTS off) until the receive FIFO reaches the upper limit of the hysteresis level. The RTS# pin will return
LOW after the RX FIFO is unloaded to the lower limit of the hysteresis level. Under the above described
conditions, the V2751 will continue to accept data until the receive FIFO gets full. The Auto RTS function is
initiated when the RTS# output pin is asserted LOW (RTS On). Table 14 shows the complete details for the
Auto RTS# Hysteresis levels. Please note that this table is for programmable trigger levels only (Table D). The
hysteresis values for Tables A-C are the next higher and next lower trigger levels in the corresponding table.
FIGURE 9. RECEIVER OPERATION IN FIFO AND AUTO RTS FLOW CONTROL MODE
Receive Data Shift
Register (RSR)
RXFIFO1
16X or 8X Clock
(EMSR bit-7)
Er
ro
rT
a
g
s
(6
4-set
s
)
E
rro
rT
a
g
s
in
LSR
bits
4:2
64 bytes by 11-bit
wide
FIFO
Receive Data Characters
FIFO
Trigger=16
Example
:
- RX FIFO trigger level selected at 16
bytes
(See Note Below)
Data fills to
24
Data falls to
8
Data Bit
Validation
Receive
Data FIFO
Receive
Data
Receive Data
Byte and Errors
RHR Interrupt (ISR bit-2) programmed for
desired FIFO trigger level.
FIFO is Enabled by FCR bit-0=1
RTS# de-asserts when data fills above the flow
control trigger level to suspend remote transmitter.
Enable by EFR bit-6=1, MCR bit-1.
RTS# re-asserts when data falls below the flow
control trigger level to restart remote transmitter.
Enable by EFR bit-6=1, MCR bit-1.
相關PDF資料
PDF描述
XR16V2752IJ-F IC UART FIFO 64B DUAL 44PLCC
XR16V554IVTR-F IC UART FIFO 16B QUAD 64LQFP
XR16V564IJ-F IC UART FIFO 32B QUAD 68PLCC
XR16V598IQ100-F IC UART FIFO 16B OCTAL 100QFP
XR16V654DIV-F IC UART FIFO 64B QUAD 64LQFP
相關代理商/技術參數
參數描述
XR16V2752 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752_07 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752IJ 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752IJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V2752IJTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:XR16V2752IJTR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*