- 您現在的位置：買賣IC網 > PDF目錄16526 > XR16M580IM48-0A-EB (Exar Corporation)EVAL BOARD FOR XR16M580-A 48TQFP PDF資料下載
參數資料
| 型號： | XR16M580IM48-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 24/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16M580-A 48TQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
XR16M580
30
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO
REV. 1.0.0
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
enable the wake up interrupt. They are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: Enable wake up interrupt (requires EFR bit-4 = 1)
Logic 0 = Disable the wake up interrupt (default).
Logic 1 = Enable the wake up interrupt.
Please refer to “Section 2.17.3, Wake-up Interrupt” on page 22.
FCR[5:4]: Transmit FIFO Trigger Select (requires EFR bit-4 = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 9 below shows the selections. Note that the
receiver and the transmitter cannot use different trigger tables. Whichever selection is made last applies to
both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 9 shows the complete selections.
Note that the receiver and the transmitter cannot use different trigger tables. Whichever selection is made last
applies to both the RX and TX side.
相關PDF資料 |
PDF描述 |
|---|---|
| 6374109-1 | C/A 62.5/125 1.6MM LC 1M |
| GBA32DTAD | CONN EDGECARD 64POS R/A .125 SLD |
| XR16M580IL32-0A-EB | EVAL BOARD FOR XR16M580-A 32QFN |
| TC54VN1402ECB713 | IC VOLT DETECTOR 1.4V SOT23A-3 |
| 6374110-8 | C/A SM, LC TO LC 1METER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M580IM48-0C-EB | 功能描述:界面開發工具 Eval Board for XR16M580IM48 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M580IM48-F | 功能描述:UART 接口集成電路 1.8 High Performance UART w/16 Byte FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M581 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 16-BYTE FIFO AND VLIO INTERFACE |
| XR16M581IB25 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 16-BYTE FIFO AND VLIO INTERFACE |
| XR16M581IB25-0C-EB | 功能描述:界面開發工具 Eval Board for XR16M581IB25 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。