參數資料
型號： XR16M564IV-0B-EVB
廠商： Exar Corporation
文件頁數： 27/55頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16M564-B 64LQFP
標準包裝： 1
系列： *
XR16M564/564D
33
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 13.
MCR[5]: Xon-Any Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO , unless the RX character is an Xon or Xoff character and
the M564 is programmed to use the Xon/Xoff flow control.
MCR[6]: Infrared Encoder/Decoder Enable (requires EFR bit-4 = 1)
Logic 0 = Enable the standard modem receive and transmit input/output interface. (Default)
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. The RX FIFO may need to be flushed upon enable. While in this mode, the infrared TX output
will be LOW during idle data conditions.
MCR[7]: Clock Prescaler Select (requires EFR bit-4 = 1)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
TABLE 14: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相關PDF資料
PDF描述
SI3056PPT-EVB BOARD EVAL FOR DAA SI3056/SI3018
A1DXB-5036G IDC CABLE- AKR50B/AE50G/X
RSC08DRYN CONN EDGECARD 16POS DIP .100 SLD
1906054-7 CA 2MM OFNR 62.5/125,LC SEC GRE
A2MXS-6418M ADM64S/AE64M/X
相關代理商/技術參數
參數描述
XR16M564IV64 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564IV64-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M564IV80 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564IV80-0A-EB 功能描述:界面開發工具 Eval Board for XR16M564IV80-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M564IV80-0B-EB 功能描述:界面開發工具 Eval Board for XR16M564IV80-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*