參數資料
型號: XR16M564IV-0A-EVB
廠商: Exar Corporation
文件頁數: 45/55頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR16M564-A 64LQFP
標準包裝: 1
系列: *
XR16M564/564D
5
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
CSB#
(A3)
9
11
20
33
I
When 16/68# pin is HIGH, this input is chip select B
(active low) to enable channel B in the device.
When 16/68# pin is LOW, this input becomes address
line A3 which is used for channel selection in the
Motorola bus interface.
CSC#
(A4)
27
38
50
68
I
When 16/68# pin is HIGH, this input is chip select C
(active low) to enable channel C in the device.
When 16/68# pin is LOW, this input becomes address
line A4 which is used for channel selection in the
Motorola bus interface.
CSD#
(VCC)
31
42
54
73
I
When 16/68# pin is HIGH, this input is chip select D
(active low) to enable channel D in the device.
When 16/68# pin is LOW, this input is not used and
should be connected VCC.
INTA
(IRQ#)
4
6
15
27
O
(OD)
When 16/68# pin is HIGH for Intel bus interface, this
ouput becomes channel A interrupt output. The output
state is defined by the user and through the software
setting of MCR[3]. INTA is set to the active mode when
MCR[3] is set to a logic 1. INTA is set to the three state
mode when MCR[3] is set to a logic 0 (default). See
MCR[3].
When 16/68# pin is LOW for Motorola bus interface,
this output becomes device interrupt output (active
low, open drain). An external pull-up resistor is
required for proper operation.
INTB
INTC
INTD
(N.C.)
10
26
32
12
37
43
21
49
55
34
67
74
O
When 16/68# pin is HIGH for Intel bus interface, these
ouputs become the interrupt outputs for channels B, C,
and D. The output state is defined by the user through
the software setting of MCR[3]. The interrupt outputs
are set to the active mode when MCR[3] is set to a
logic 1 and are set to the three state mode when
MCR[3] is set to a logic 0 (default). See MCR[3].
When 16/68# pin is LOW for Motorola bus interface,
these outputs are unused and will stay at logic zero
level. Leave these outputs unconnected.
TXRDY#
-
39
55
O
Transmitter Ready (active low). This output is a logi-
cally ANDed status of TXRDY# A-D. See Table 5. If
this output is unused, leave it unconnected.
RXRDY#
-
38
54
O
Receiver Ready (active low). This output is a logically
ANDed status of RXRDY# A-D. See Table 5. If this
output is unused, leave it unconnected.
Pin Description
NAME
48-QFN
PIN #
64-LQFP
PIN #
68-PLCC
PIN #
80-LQFP
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
VI-J2H-EZ-S CONVERTER MOD DC/DC 52V 25W
2-5504971-8 CA 62.5/125 LDDZP SCDUP SCDUP
EEC08DRAS-S734 CONN EDGECARD 16POS .100 R/A PCB
CB5000-000 HEAT SHRINK TUBING
XR16M654IQ100-0B-EB EVAL BOARD FOR XR16M654-B 100QFP
相關代理商/技術參數
參數描述
XR16M564IV-0B-EVB 功能描述:界面開發工具 Eval Board for XR16M564IV-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M564IV64 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564IV64-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M564IV80 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564IV80-0A-EB 功能描述:界面開發工具 Eval Board for XR16M564IV80-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V