- 您現在的位置：買賣IC網 > PDF目錄16501 > XR16M564IL-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16M564-A 48QFN PDF資料下載
參數資料
| 型號： | XR16M564IL-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 22/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16M564-A 48QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XR16M564/564D
29
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
]
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source
Table 11).
ISR[4]: Interrupt Status (requires EFR bit-4 = 1)
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-4 indicates that the receiver detected a data match
of the Xoff character(s) or a special character.
ISR[5]: Interrupt Status (requires EFR bit-4 = 1)
ISR bit-5 indicates that CTS# or RTS# has changed state from LOW to HIGH.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
TABLE 11: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Receive Data Time-out)
3
0
1
0
RXRDY (Received Data Ready)
4
0
1
0
TXRDY (Transmit Ready)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xoff or Special character)
7
1
0
CTS#, RTS# change of state
-
0
1
None (default)
相關PDF資料 |
PDF描述 |
|---|---|
| M3UUK-1020K | IDC CABLE - MKS10K/MC10F/MKS10K |
| SI3050PPT-EVB | BOARD EVAL FOR DAA SI3050/SI3019 |
| M3TKK-1018R | IDC CABLE - MSD10K/MC10M/MPK10K |
| VE-JNX-EZ-S | CONVERTER MOD DC/DC 5.2V 25W |
| RHW-9/3-1200/ADH-0 | HEATSHRINK RHW POLY 9MMX4' BLK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M564IL-0B-EVB | 功能描述:界面開發工具 Eval Board for XR16M564IL-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M564IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M564IV-0A-EVB | 功能描述:界面開發工具 Eval Board for XR16M564IV-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M564IV-0B-EVB | 功能描述:界面開發工具 Eval Board for XR16M564IV-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。