- 您現在的位置：買賣IC網 > PDF目錄16507 > XR16M554IJ-0B-EVB (Exar Corporation)EVAL BOARD FOR XR16M554-B 68PLCC PDF資料下載
參數資料
| 型號： | XR16M554IJ-0B-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 42/46頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16M554-B 68PLCC |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁
XR16M554/554D
5
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
CSB#
(A3)
9
11
20
33
I
When 16/68# pin is HIGH, this input is chip select B
(active low) to enable channel B in the device.
When 16/68# pin is LOW, this input becomes address
line A3 which is used for channel selection in the Motor-
ola bus interface.
CSC#
(A4)
27
38
50
68
I
When 16/68# pin is HIGH, this input is chip select C
(active low) to enable channel C in the device.
When 16/68# pin is LOW, this input becomes address
line A4 which is used for channel selection in the Motor-
ola bus interface.
CSD#
(VCC)
31
42
54
73
I
When 16/68# pin is HIGH, this input is chip select D
(active low) to enable channel D in the device.
When 16/68# pin is LOW, this input is not used and
should be connected VCC.
INTA
(IRQ#)
4
6
15
27
O
(OD)
When 16/68# pin is HIGH for Intel bus interface, this
ouput becomes channel A interrupt output. The output
state is defined by the user and through the software
setting of MCR[3]. INTA is set to the active mode when
MCR[3] is set to a logic 1. INTA is set to the three state
mode when MCR[3] is set to a logic 0 (default). See
MCR[3].
When 16/68# pin is LOW for Motorola bus interface,
this output becomes device interrupt output (active low,
open drain). An external pull-up resistor is required for
proper operation.
INTB
INTC
INTD
(N.C.)
10
26
32
12
37
43
21
49
55
34
67
74
O
When 16/68# pin is HIGH for Intel bus interface, these
ouputs become the interrupt outputs for channels B, C,
and D. The output state is defined by the user through
the software setting of MCR[3]. The interrupt outputs
are set to the active mode when MCR[3] is set to a logic
1 and are set to the three state mode when MCR[3] is
set to a logic 0 (default). See MCR[3].
When 16/68# pin is LOW for Motorola bus interface,
these outputs are unused and will stay at logic zero
level. Leave these outputs unconnected.
TXRDY#
-
39
55
O
Transmitter Ready (active low). This output is a logi-
cally ANDed status of TXRDY# A-D. See Table 5. If this
output is unused, leave it unconnected.
RXRDY#
-
38
54
O
Receiver Ready (active low). This output is a logically
ANDed status of RXRDY# A-D. See Table 5. If this out-
put is unused, leave it unconnected.
Pin Description
NAME
48-QFN
PIN #
64-LQFP
PIN #
68-PLCC
PIN#
80-LQFP
PIN #
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| M1AXK-1640K | IDC CABLE - MSC16K/MC16F/X |
| XR16M554IJ-0A-EVB | EVAL BOARD FOR XR16M554-A 68PLCC |
| VI-2TL-EX | CONVERTER MOD DC/DC 28V 75W |
| 6278879-3 | C/A 50/125UM RIS MTRJ 3M1 |
| H3DKH-4036G | IDC CABLE - HKR40H/AE40G/HPK40H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M554IJ68 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO |
| XR16M554IJ68-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M554IL-0A-EVB | 功能描述:界面開發工具 Eval Board for XR16M554IL-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M554IL-0B-EVB | 功能描述:界面開發工具 Eval Board for XR16M554IL-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M554IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。