參數資料
型號： XR16M554IJ-0A-EVB
廠商： Exar Corporation
文件頁數： 5/46頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16M554-A 68PLCC
標準包裝： 1
系列： *
XR16M554/554D
13
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
2.7
Crystal Oscillator or External Clock Input
The M554 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. For programming details, see
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins. Typical oscillator connections are shown
in Figure 5. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal baud rate
generator for standard or custom rates. For further reading on oscillator circuit please see application note
DAN108 on EXAR’s web site.
2.8
Programmable Baud Rate Generator
Each UART has its own Baud Rate Generator (BRG) for the transmitter and receiver. The BRG further divides
this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to obtain a
16X sampling rate clock of the serial data rate. The sampling rate clock is used by the transmitter for data bit
shifting and receiver for data sampling. The BRG divisor defaults to the maximum baud rate (DLL = 0x01 and
DLM = 0x00) upon power up and reset. Programming the Baud Rate Generator Registers DLL and DLM
provides the capability for selecting the operating data rate. Table 6 shows the standard data rates available
with a 24MHz crystal or external clock at 16X clock rate. If the pre-scaler is used (MCR bit-7 = 1), the output
data rate will be 4 times less than that shown in Table 6.
TABLE 5: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE FOR CHANNELS A-D
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR BIT-3 = 0
(DMA MODE DISABLED)
FCR BIT-3 = 1
(DMA MODE ENABLED)
RXRDY#
LOW = 1 byte
HIGH = no data
LOW = at least 1 byte in FIFO
HIGH = FIFO empty
HIGH to LOW transition when FIFO reaches the
trigger level, or timeout occurs
LOW to HIGH transition when FIFO empties
TXRDY#
LOW = THR empty
HIGH = byte in THR
LOW = FIFO empty
HIGH = at least 1 byte in FIFO
LOW = FIFO has at least 1 empty location
HIGH = FIFO is full
FIGURE 5. TYPICAL CRYSTAL CONNECTIONS
C1
22-47pF
C2
22-47pF
14.7456
MHz
XTAL1
XTAL2
R=300K to 400K
相關PDF資料
PDF描述
VI-2TL-EX CONVERTER MOD DC/DC 28V 75W
6278879-3 C/A 50/125UM RIS MTRJ 3M1
H3DKH-4036G IDC CABLE - HKR40H/AE40G/HPK40H
RCC18DCAD CONN EDGECARD 36POS R/A .100 SLD
IMC0402ER22NJ INDUCTOR 22NH 5% 0402
相關代理商/技術參數
參數描述
XR16M554IJ-0B-EVB 功能描述:界面開發工具 Eval Board for XR16M554IJ-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M554IJ68 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
XR16M554IJ68-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M554IL-0A-EVB 功能描述:界面開發工具 Eval Board for XR16M554IL-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M554IL-0B-EVB 功能描述:界面開發工具 Eval Board for XR16M554IL-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*