REV. 1.2.1 10 The on-chip oscillator is designed to use an industry standard microprocessor " />
參數資料
型號： XR16L2750CMTR-F
廠商： Exar Corporation
文件頁數： 2/48頁
文件大?。?/td> 0K
描述： IC UART FIFO 64B DUAL 48TQFP
標準包裝： 1,500
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS485
電源電壓： 2.25 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 帶卷 (TR)
XR16L2750
xr
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.2.1
10
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100 ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 4). The programmable Baud
Rate Generator is capable of operating with a crystal oscillator frequency of up to 24 MHz. However, with an
external clock input on XTAL1 pin and a 2K ohms pull-up resistor on XTAL2 pin (as shown in Figure 5) it can
extend its operation up to 50 MHz (6.25 Mbps serial data rate) at 5V with an 8X sampling rate.
For further reading on the oscillator circuit please see the Application Note DAN108 on the EXAR web site at
2.10
Programmable Baud Rate Generator
Each UART has its own Baud Rate Generator (BRG) with a prescaler. The prescaler is controlled by a
software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide the input crystal or external
clock by 1 or 4. The clock output of the prescaler goes to the BRG. The BRG further divides this clock by a
programmable divisor between 1 and (216 -1) to obtain a 16X sampling rate clock of the serial data rate. The
sampling rate clock is used by the transmitter for data bit shifting and receiver for data sampling. The BRG
divisor defaults to the maximum baud rate (DLL = 0x01 and DLM = 0x00) upon power up.
Programming the Baud Rate Generator Registers DLM and DLL provides the capability of selecting the
operating data rate. Table 5 shows the standard data rates available with a 14.7456 MHz crystal or external
clock at 16X sampling rate clock rate. A 16X sampling clock is typically used. However, user can select the 8X
FIGURE 5. EXTERNAL CLOCK CONNECTION FOR EXTENDED DATA RATE
FIGURE 6. BAUD RATE GENERATOR AND PRESCALER
2K
XTAL1
XTAL2
R1
VCC
External Clock
vcc
gnd
XTAL1
XTAL2
Crystal
Osc/
Buffer
MCR Bit-7=0
(default)
MCR Bit-7=1
DLL and DLM
Registers
Prescaler
Divide by 1
Prescaler
Divide by 4
16X
Sampling
Rate Clock to
Transmitter
Baud Rate
Generator
Logic
相關PDF資料
PDF描述
XR16V2550ILTR-F IC UART FIFO 16B DUAL 32QFN
ATMEGA324PA-MUR MCU AVR 32KB FLASH 20 MHZ 44QFN
ST78C36CJ44TR-F IC UART FIFO 16B 44PLCC
XR16L2550IMTR-F IC UART FIFO 16B DUAL 48TQFP
XR16M780IL32-F IC UART FIFO 64B 32QFN
相關代理商/技術參數
參數描述
XR16L2750IJ 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750IJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2750IM 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750IM-F 功能描述:UART 接口集成電路 2.25V-5.5V 64B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2750IMTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*