REV. 2.1.1 4 RXA 39 I UART channel A Receive Data or infrared receive data. Normal rec" />
參數資料
型號： XR16C2852IJTR-F
廠商： Exar Corporation
文件頁數： 34/51頁
文件大?。?/td> 0K
描述： IC UART FIFO 128B 44PLCC
標準包裝： 500
特點： *
通道數： 2，DUART
FIFO's： 128 字節
規程： RS232，RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 帶卷 (TR)
XR16C2852
xr
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
REV. 2.1.1
4
RXA
39
I
UART channel A Receive Data or infrared receive data. Normal receive data input
must idleHIGH. The infrared receiver pulses typically idles LOW but can be inverted
by software control prior going in to the decoder, see MCR[6] and FCTR[2]. If this pin
is not used, tie it to VCC or pull it high via a 100k ohm resistor.
RTSA#
36
O
UART channel A Request-to-Send (active low) or general purpose output. This output
must be asserted (LOW) prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-duplex direction control, see
FCTR[3]. If this output is not used, leave it unconnected.
CTSA#
40
I
UART channel A Clear-to-Send (active low) or general purpose input. It can be used
for auto CTS flow control, see EFR[7], and IER[7]. This input should be connected to
VCC when not used.
DTRA#
37
O
UART channel A Data-Terminal-Ready (active low) or general purpose output. If this
output is not used, leave it unconnected.
DSRA#
41
I
UART channel A Data-Set-Ready (active low) or general purpose input. This input
should be connected to VCC when not used.
CDA#
42
I
UART channel A Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used.
RIA#
43
I
UART channel A Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used.
MFA#
35
O
Multi-Function Output Channel A. This output pin can function as the OP2A#, BAUD-
OUTA#, or RXRDYA# pin. One of these output signal functions can be selected by
the user programmable bits 1-2 of the Alternate Function Register (AFR). These sig-
nal functions are described as follows:
1) OP2A# - When OP2A# (active low) is selected, the MF# pin is LOW when MCR bit-
3 is set to a logic 1 (see MCR bit-3). MCR bit-3 defaults to a logic 0 condition after a
reset or power-up.
2) BAUDOUTA# - When BAUDOUTA# function is selected, the 16X Baud rate clock
output is available at this pin.
3) RXRDYA# - RXRDYA# (active low) is intended for monitoring DMA data transfers.
See
Table 2 on page 9 for more details.
If this output is not used, leave it unconnected.
TXB
26
O
UART channel B Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be
HIGH during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is LOW. If this output is not used, leave it uncon-
nected.
RXB
25
I
UART channel B Receive Data or infrared receive data. Normal receive data input
must idle HIGH. The infrared receiver pulses typically idles LOW but can be inverted
by software control prior going in to the decoder, see MCR[6] and FCTR[2]. If this pin
is not used, tie it to VCC or pull it high via a 100k ohm resistor.
Pin Description
NAME
44-PLCC
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
XR16C2850IJTR-F IC UART FIFO 128B 44PLCC
XR16V554IV-F IC UART FIFO 16B QUAD 64LQFP
VE-B5L-IW-F1 CONVERTER MOD DC/DC 28V 100W
VE-B5L-IX-F4 CONVERTER MOD DC/DC 28V 75W
VE-B5L-IX-F2 CONVERTER MOD DC/DC 28V 75W
相關代理商/技術參數
參數描述
XR-16C450CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
XR-16C450CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
XR-16C452CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
XR-16C550CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
XR-16C550CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*