- 您現在的位置：買賣IC網 > PDF目錄300157 > XCS30XL-4PC208C (Xilinx, Inc.) Spartan and Spartan-XL Families Field Programmable Gate Arrays PDF資料下載
參數資料
| 型號： | XCS30XL-4PC208C |
| 廠商： | Xilinx, Inc. |
| 英文描述： | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| 中文描述： | 斯巴達和Spartan - xL的家庭現場可編程門陣列 |
| 文件頁數： | 2/82頁 |
| 文件大?。?/td> | 863K |
| 代理商： | XCS30XL-4PC208C |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
Spartan and Spartan-XL Families Field Programmable Gate Arrays
10
DS060 (v1.6) September 19, 2001
1-800-255-7778
Product Specification
R
Over Operating Conditions" on page 43.). This high value
makes them unsuitable as wired-AND pull-up resistors.
After configuration, voltage levels of unused pads, bonded
or unbonded, must be valid logic levels, to reduce noise
sensitivity and avoid excess current. Therefore, by default,
unused pads are configured with the internal pull-up resistor
active. Alternatively, they can be individually configured with
the pull-down resistor, or as a driven output, or to be driven
by an external source. To activate the internal pull-up, attach
the PULLUP library component to the net attached to the
pad. To activate the internal pull-down, attach the PULL-
DOWN library component to the net attached to the pad.
Set/Reset
As with the CLB registers, the GSR signal can be used to
set or clear the input and output registers, depending on the
value of the INIT attribute or property. The two flip-flops can
be individually configured to set or clear on reset and after
configuration. Other than the global GSR net, no user-con-
trolled set/reset signal is available to the I/O flip-flops
(Figure 5). The choice of set or reset applies to both the ini-
tial state of the flip-flop and the response to the GSR pulse.
Independent Clocks
Separate clock signals are provided for the input (IK) and
output (OK) flip-flops. The clock can be independently
inverted for each flip-flop within the IOB, generating either
falling-edge or rising-edge triggered flip-flops. The clock
inputs for each IOB are independent.
Common Clock Enables
The input and output flip-flops in each IOB have a common
clock enable input (see EC signal in Figure 5), which
through configuration, can be activated individually for the
input or output flip-flop, or both. This clock enable operates
exactly like the EC signal on the Spartan/XL CLB. It cannot
be inverted within the IOB.
Routing Channel Description
All internal routing channels are composed of metal seg-
ments with programmable switching points and switching
matrices to implement the desired routing. A structured,
hierarchical matrix of routing channels is provided to
achieve efficient automated routing.
This section describes the routing channels available in
Spartan/XL devices. Figure 8 shows a general block dia-
gram of the CLB routing channels. The implementation soft-
ware automatically assigns the appropriate resources
based on the density and timing requirements of the design.
The following description of the routing channels is for infor-
mation only and is simplified with some minor details omit-
ted. For an exact interconnect description the designer
should open a design in the FPGA Editor and review the
actual connections in this tool.
The routing channels will be discussed as follows;
CLB routing channels which run along each row and
column of the CLB array.
IOB routing channels which form a ring (called a
VersaRing) around the outside of the CLB array. It
connects the I/O with the CLB routing channels.
Global routing consists of dedicated networks primarily
designed to distribute clocks throughout the device with
minimum delay and skew. Global routing can also be
used for other high-fanout signals.
CLB Routing Channels
The routing channels around the CLB are derived from
three types of interconnects; single-length, double-length,
and longlines. At the intersection of each vertical and hori-
zontal routing channel is a signal steering matrix called a
Programmable Switch Matrix (PSM). Figure 8 shows the
basic routing channel configuration showing single-length
lines, double-length lines and longlines as well as the CLBs
and PSMs. The CLB to routing channel interface is shown
as well as how the PSMs interface at the channel intersec-
tions.
Table 7: Supported Destinations for Spartan/XL
Outputs
Destination
Spartan-XL
Outputs
Spartan
Outputs
3.3V, CMOS
5V,
TTL
5V,
CMOS
Any device,
VCC = 3.3V,
CMOS-threshold
inputs
√√
Some(1)
Any device,
VCC = 5V,
TTL-threshold inputs
√√
√
Any device,
VCC = 5V,
CMOS-threshold
inputs
Unreliable
Data
√
Notes:
1.
Only if destination device has 5V tolerant inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| XCS30XL-4PC208I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC240C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC240I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC256C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC256I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCS30XL-4PC208I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC240C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC240I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC256C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4PC256I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。