- 您現在的位置：買賣IC網 > PDF目錄375006 > XCCACEM64BG388I (XILINX INC) System ACE MPM Solution PDF資料下載
參數資料
| 型號： | XCCACEM64BG388I |
| 廠商： | XILINX INC |
| 元件分類： | 存儲器 |
| 英文描述： | System ACE MPM Solution |
| 中文描述： | SPECIALTY MEMORY CIRCUIT, PBGA388 |
| 封裝： | 35 X 35 MM, 2.70 MM HEIGHT, BGA-388 |
| 文件頁數： | 6/29頁 |
| 文件大?。?/td> | 283K |
| 代理商： | XCCACEM64BG388I |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
System ACE
MPM Solution
6
www.xilinx.com
1-800-255-7778
DS087 (v1.2) June 7, 2002
Advance Product Specification
R
Pin Name
Pin Type
Description
CFG_DATA[6]
Output
For Slave-Serial configuration mode, CFG_DATA[6] is the serial data signal for
Serial-Slave Chain 6 and is connected to DIN of the first FPGA in the
Slave-Serial Chain 6. For Slave-SelectMAP configuration mode, CFG_DATA[6]
is the data bit 6 on the SelectMAP bus and is connected to D6 on all target
FPGAs.
CFG_DATA[7]
Output
For Slave-Serial configuration mode, CFG_DATA[7] is the serial data signal for
Serial-Slave Chain 7 and is connected to DIN of the first FPGA in the
Slave-Serial Chain 7. For Slave-SelectMAP configuration mode, CFG_DATA[7]
is the data bit 7 on the SelectMAP bus and is connected to D7 on all target
FPGAs.
CFG_MODE[0]
Output
The CFG_MODE pins set the configuration mode on the target FPGAs.
Connect CFG_MODE[0] to the M0 pin on all target FPGAs.
CFG_MODE[1]
Output
The CFG_MODE pins set the configuration mode on the target FPGAs.
Connect CFG_MODE[1] to the M1 pin on all target FPGAs.
CFG_MODE[2]
Output
The CFG_MODE pins set the configuration mode on the target FPGAs.
Connect CFG_MODE[2] to the M2 pin on all target FPGAs.
CFG_CCLK
Output
CFG_CCLK is the configuration clock source for the target FPGAs. The
CFG_CCLK is derived from the SYSCLK. The CFG_CCLK frequency is half
the SYSCLK frequency. Connect CFG_CCLK to the CCLK pin on all target
FPGAs.
CFG_PROG
Output
CFG_PROG is pulsed Low at the beginning of the configuration download to
reset the configuration state of the target FPGAs. CFG_PROG is connected to
the PROG_B pin on all target FPGAs.
CFG_INIT
Input
Target FPGA INIT monitor pin. At the start of the configuration process, the
System ACE MPM controller waits for INIT to go High before initiating delivery
of configuration data through the CFG_DATA pins. CFG_INIT is connected to
the INIT pin on all target FPGAs.
CFG_BUSY
Input
When CFG_BUSY is High, the CFG_DATA outputs are held. If the target FPGA
configuration mode is Slave-SelectMAP and if the CFG_CCLK is greater than
50 MHz, connect the CFG_BUSY pin to the BUSY pin on all target FPGAs.
Otherwise, pull-down the CFG_BUSY pin to GND.
CFG_DONE
Input
CFG_DONE monitors the DONE status on all target FPGAs. Connect the
CFG_DONE to the DONE pin on all target FPGAs. DONE must be pulled High
with an external 330-
pull-up resistor. The BitGen option DriveDONE should
be left in the default
“
NO
”
setting when generating bitstreams for Xilinx FPGAs.
CFG_WRITE
Output
Slave-SelectMAP write-enable pin. Connect the CFG_WRITE pin to the
RDWR_B pin on all target FPGAs.
CFG_CS[0]
Output
Slave-SelectMAP chip-enable for target FPGA 0. Connect the CFG_CS[0] pin
to the CS_B pin on target FPGA 0.
CFG_CS[1]
Output
Slave-SelectMAP chip-enable for target FPGA 1. Connect the CFG_CS[1] pin
to the CS_B pin on target FPGA 1.
CFG_CS[2]
Output
Slave-SelectMAP chip-enable for target FPGA 2. Connect the CFG_CS[2] pin
to the CS_B pin on target FPGA 2.
CFG_CS[3]
Output
Slave-SelectMAP chip-enable for target FPGA 3. Connect the CFG_CS[3] pin
to the CS_B pin on target FPGA 3.
Table 3:
Target FPGA Configuration Pins
(Continued)
相關PDF資料 |
PDF描述 |
|---|---|
| XCF01SF48 | Platform Flash In-System Programmable Configuration PROMS |
| XCF01SFG48 | Platform Flash In-System Programmable Configuration PROMS |
| XCF01SV | Platform Flash In-System Programmable Configuration PROMS |
| XCF01SVG | Platform Flash In-System Programmable Configuration PROMS |
| XCF01SVO20C | Platform Flash In-System Programmable Configuration PROMS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCCACEM64-BG388I | 功能描述:SYS ACE MULTIPKG MODULE 64MBIT RoHS:否 類別:存儲卡，模塊 >> 存儲器 - 模塊 系列:- 標準包裝:100 系列:- 存儲器類型:SDRAM 存儲容量:1GB 速度:133MHz 特點:- 封裝/外殼:168-DIMM |
| XCCACEM64SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:System ACE MPM Solution |
| XCCACESERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:System ACE CompactFlash Solution |
| XCCACE-TQ144 | 制造商:XILINX 制造商全稱:XILINX 功能描述:System ACE CompactFlash Solution |
| XCCACE-TQ144I | 功能描述:IC ACE CONTROLLER CHIP RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。