參數資料
型號： XC5206-5PC84I
英文描述： Field Programmable Gate Array (FPGA)
中文描述： 現場可編程門陣列（FPGA）
文件頁數： 18/73頁
文件大?。?/td> 598K
代理商： XC5206-5PC84I
R
XC5200 Series Field Programmable Gate Arrays
7-100
November 5, 1998 (Version 5.2)
XC5200-Series devices can also be configured through the
boundary scan logic. See XAPP 017 for more information.
Data Registers
The primary data register is the boundary scan register.
For each IOB pin in the FPGA, bonded or not, it includes
three bits for In, Out and 3-State Control. Non-IOB pins
have appropriate partial bit population for In or Out only.
PROGRAM, CCLK and DONE are not included in the
boundary scan register. Each EXTEST CAPTURE-DR
state captures all In, Out, and 3-State pins.
The data register also includes the following non-pin bits:
TDO.T, and TDO.O, which are always bits 0 and 1 of the
data register, respectively, and BSCANT.UPD, which is
always the last bit of the data register. These three bound-
ary scan bits are special-purpose Xilinx test signals.
The other standard data register is the single flip-flop
BYPASS register. It synchronizes data being passed
through the FPGA to the next downstream boundary scan
device.
The FPGA provides two additional data registers that can
be specified using the BSCAN macro. The FPGA provides
two user pins (BSCAN.SEL1 and BSCAN.SEL2) which are
the decodes of two user instructions, USER1 and USER2.
For
these
instructions,
(BSCAN.TDO1 and BSCAN.TDO2) allow user scan data to
be shifted out on TDO. The data register clock
(BSCAN.DRCK) is available for control of test logic which
the user may wish to implement with CLBs. The NAND of
TCK and RUN-TEST-IDLE is also provided (BSCAN.IDLE).
two
corresponding
pins
Instruction Set
The XC5200-Series boundary scan instruction set also
includes instructions to configure the device and read back
the configuration data. The instruction set is coded as
shown in
Table 7
.
Table 7: Boundary Scan Instructions
Bit Sequence
The bit sequence within each IOB is: 3-State, Out, In. The
data-register cells for the TAP pins TMS, TCK, and TDI
have an OR-gate that permanently disables the output
buffer if boundary-scan operation is selected. Conse-
quently, it is impossible for the outputs in IOBs used by TAP
inputs to conflict with TAP operation. TAP data is taken
directly from the pin, and cannot be overwritten by injected
boundary-scan data.
The primary global clock inputs (PGCK1-PGCK4) are
taken directly from the pins, and cannot be overwritten with
boundary-scan data. However, if necessary, it is possible to
drive the clock input from boundary scan. The external
clock source is 3-stated, and the clock net is driven with
boundary scan data through the output driver in the
clock-pad IOB. If the clock-pad IOBs are used for non-clock
signals, the data may be overwritten normally.
Pull-up and pull-down resistors remain active during
boundary scan. Before and during configuration, all pins
are pulled up. After configuration, the choice of internal
pull-up or pull-down resistor must be taken into account
when designing test vectors to detect open-circuit PC
traces.
From a cavity-up view of the chip (as shown in XDE or
Epic), starting in the upper right chip corner, the boundary
scan data-register bits are ordered as shown in
Table 8
.
The device-specific pinout tables for the XC5200 Series
include the boundary scan locations for each IOB pin.
Table 8: Boundary Scan Bit Sequence
BSDL (Boundary Scan Description Language) files for
XC5200-Series devices are available on the Xilinx web site
in the File Download area.
Including Boundary Scan
If boundary scan is only to be used during configuration, no
special elements need be included in the schematic or HDL
code. In this case, the special boundary scan pins TDI,
TMS, TCK and TDO can be used for user functions after
configuration.
To indicate that boundary scan remain enabled after config-
uration, include the BSCAN library symbol and connect pad
symbols to the TDI, TMS, TCK and TDO pins, as shown in
Figure 20
.
Instruction I2
I1 I0
0
0
0
0
Test
Selected
EXTEST
SAMPLE/PR
ELOAD
USER 1
TDO Source
I/O Data
Source
DR
Pin/Logic
0
1
DR
DR
0
1
0
BSCAN.
TDO1
BSCAN.
TDO2
User Logic
0
1
1
USER 2
User Logic
1
0
0
READBACK Readback
Data
DOUT
—
Bypass
Register
Pin/Logic
1
1
1
0
1
1
1
0
1
CONFIGURE
Reserved
BYPASS
Disabled
—
—
Bit Position
Bit 0 (TDO)
Bit 1
...
...
...
Bit N (TDI)
I/O Pad Location
Top-edge I/O pads (right to left)
...
Left-edge I/O pads (top to bottom)
Bottom-edge I/O pads (left to right)
Right-edge I/O pads (bottom to top)
BSCANT.UPD
相關PDF資料
PDF描述
XC5206-6PC84I Field Programmable Gate Array (FPGA)
XC5206-6PQ100I Field Programmable Gate Array (FPGA)
XC5206-6PQ160I Field Programmable Gate Array (FPGA)
XC5206-6PQ208I Field Programmable Gate Array (FPGA)
XC5210-3PC84I Field Programmable Gate Array (FPGA)
相關代理商/技術參數
參數描述
XC5206-5PG156C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5206-5PG191C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5206-5PG223C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5206-5PG299C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5206-5PQ100C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*