- 您現在的位置：買賣IC網 > PDF目錄371339 > XC5204-3VQ100I Field Programmable Gate Array (FPGA) PDF資料下載
參數資料
| 型號： | XC5204-3VQ100I |
| 英文描述： | Field Programmable Gate Array (FPGA) |
| 中文描述： | 現場可編程門陣列（FPGA） |
| 文件頁數： | 11/73頁 |
| 文件大?。?/td> | 598K |
| 代理商： | XC5204-3VQ100I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
R
November 5, 1998 (Version 5.2)
7-93
XC5200 Series Field Programmable Gate Arrays
7
to Vcc. The configurable pull-down resistor is an n-channel
transistor that pulls to Ground.
The value of these resistors is 20 k
100 k
. This high
value makes them unsuitable as wired-AND pull-up resis-
tors.
The pull-up resistors for most user-programmable IOBs are
active during the configuration process. See
Table 13 on
page 124
for a list of pins with pull-ups active before and
during configuration.
After configuration, voltage levels of unused pads, bonded
or unbonded, must be valid logic levels, to reduce noise
sensitivity and avoid excess current. Therefore, by default,
unused pads are configured with the internal pull-up resis-
tor active. Alternatively, they can be individually configured
with the pull-down resistor, or as a driven output, or to be
driven by an external source. To activate the internal
pull-up, attach the PULLUP library component to the net
attached to the pad. To activate the internal pull-down,
attach the PULLDOWN library component to the net
attached to the pad.
JTAG Support
Embedded logic attached to the IOBs contains test struc-
tures compatible with IEEE Standard 1149.1 for boundary
scan testing, simplifying board-level testing. More informa-
tion is provided in
“Boundary Scan” on page 98
.
Oscillator
XC5200 devices include an internal oscillator. This oscilla-
tor is used to clock the power-on time-out, clear configura-
tion memory, and source CCLK in Master configuration
modes. The oscillator runs at a nominal 12 MHz frequency
that varies with process, Vcc, and temperature. The output
CCLK frequency is selectable as 1 MHz (default), 6 MHz,
or 12 MHz.
The XC5200 oscillator divides the internal 12-MHz clock or
a user clock. The user then has the choice of dividing by 4,
16, 64, or 256 for the “OSC1” output and dividing by 2, 8,
32, 128, 1024, 4096, 16384, or 65536 for the “OSC2” out-
put. The division is specified via a “DIVIDEn_BY=x”
attribute on the symbol, where n=1 for OSC1, or n=2 for
OSC2. These frequencies can vary by as much as -50% or
+ 50%.
The OSC5 macro is used where an internal oscillator is
required. The CK_DIV macro is applicable when a user
clock input is specified (see
Figure 13
).
VersaBlock Routing
The General Routing Matrix (GRM) connects to the
Versa-Block via 24 bidirectional ports (M0-M23). Excluding
direct connections, global nets, and 3-statable Longlines,
all VersaBlock inputs and outputs connect to the GRM via
these 24 ports. Four 3-statable unidirectional signals
(TQ0-TQ3) drive out of the VersaBlock directly onto the
horizontal and vertical Longlines. Two horizontal global
nets and two vertical global nets connect directly to every
CLB clock pin; they can connect to other CLB inputs via the
GRM. Each CLB also has four unidirectional direct con-
nects to each of its four neighboring CLBs. These direct
connects can also feed directly back to the CLB (see
Figure 14
).
In addition, each CLB has 16 direct inputs, four direct con-
nections from each of the neighboring CLBs. These direct
connections provide high-speed local routing that
bypasses the GRM.
Local Interconnect Matrix
The Local Interconnect Matrix (LIM) is built from input and
output multiplexers. The 13 CLB outputs (12 LC outputs
plus a V
cc
/GND signal) connect to the eight VersaBlock
outputs via the output multiplexers, which consist of eight
fully populated 13-to-1 multiplexers. Of the eight
VersaBlock outputs, four signals drive each neighboring
CLB directly, and provide a direct feedback path to the input
multiplexers. The four remaining multiplexer outputs can
drive the GRM through four TBUFs (TQ0-TQ3). All eight
multiplexer outputs can connect to the GRM through the
bidirectional M0-M23 signals. All eight signals also connect
to the input multiplexers and are potential inputs to that
CLB.
OSCS
CK_DIV
OSC1
OSC1
OSC2
OSC2
5200_14
Figure 13: XC5200 Oscillator Macros
相關PDF資料 |
PDF描述 |
|---|---|
| XC5204-4PC84I | Field Programmable Gate Array (FPGA) |
| XC5204-5VQ100I | Field Programmable Gate Array (FPGA) |
| XC5204-6PC84I | Field Programmable Gate Array (FPGA) |
| XC5206-3PC84I | Field Programmable Gate Array (FPGA) |
| XC5206-3PG191I | Field Programmable Gate Array (FPGA) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC5204-3VQ64C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5204-4BG225C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5204-4BG352C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5204-4HQ208C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5204-4HQ240C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。