- 您現在的位置：買賣IC網 > PDF目錄4176 > XC3130A-3PC84C (Xilinx Inc)IC LOGIC CL ARRAY 3000GAT 84PLCC PDF資料下載
參數資料
| 型號： | XC3130A-3PC84C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 56/76頁 |
| 文件大小： | 0K |
| 描述： | IC LOGIC CL ARRAY 3000GAT 84PLCC |
| 標準包裝： | 15 |
| 系列： | XC3000A/L |
| LAB/CLB數： | 100 |
| RAM 位總計： | 22176 |
| 輸入/輸出數： | 74 |
| 門數： | 2000 |
| 電源電壓： | 4.25 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 84-LCC（J 形引線） |
| 供應商設備封裝： | 84-PLCC |
| 其它名稱： | 122-1040 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
R
XC3000 Series Field Programmable Gate Arrays
7-8
November 9, 1998 (Version 3.1)
The input-buffer portion of each IOB provides threshold
detection to translate external signals applied to the pack-
age pin to internal logic levels. The global input-buffer
threshold of the IOBs can be programmed to be compatible
with either TTL or CMOS levels. The buffered input signal
drives the data input of a storage element, which may be
configured as either a flip-flop or a latch. The clocking
polarity (rising/falling edge-triggered flip-flop, High/Low
transparent latch) is programmable for each of the two
clock lines on each of the four die edges. Note that a clock
line driving a
rising edge-triggered flip-flop makes any latch
driven by the same line on the same edge Low-level trans-
parent and vice versa (
falling edge, High transparent). All
Xilinx primitives in the supported schematic-entry pack-
ages, however, are positive edge-triggered flip-flops or
High transparent latches. When one clock line must drive
flip-flops as well as latches, it is necessary to compensate
for the difference in clocking polarities with an additional
inverter either in the flip-flop clock input or the latch-enable
input. I/O storage elements are reset during configuration
or by the active-Low chip RESET input. Both direct input
(from IOB pin I) and registered input (from IOB pin Q) sig-
nals are available for interconnect.
For reliable operation, inputs should have transition times
of less than 100 ns and should not be left floating. Floating
CMOS input-pin circuits might be at threshold and produce
oscillations. This can produce additional power dissipation
and system noise. A typical hysteresis of about 300 mV
reduces sensitivity to input noise. Each user IOB includes a
programmable high-impedance pull-up resistor, which may
be selected by the program to provide a constant High for
otherwise undriven package pins. Although the Field Pro-
grammable Gate Array provides circuitry to provide input
protection for electrostatic discharge, normal CMOS han-
dling precautions should be observed.
Flip-flop loop delays for the IOB and logic-block flip-flops
are short, providing good performance under asynchro-
nous clock and data conditions. Short loop delays minimize
the probability of a metastable condition that can result
from assertion of the clock during data transitions. Because
of the short-loop-delay characteristic in the Field Program-
mable Gate Array, the IOB flip-flops can be used to syn-
chronize external signals applied to the device. Once
synchronized in the IOB, the signals can be used internally
without further consideration of their clock relative timing,
except as it applies to the internal logic and routing-path
delays.
IOB output buffers provide CMOS-compatible 4-mA
source-or-sink drive for high fan-out CMOS or TTL- com-
patible signal levels (8 mA in the XC3100A family). The net-
work driving IOB pin O becomes the registered or direct
data source for the output buffer. The 3-state control signal
(IOB) pin T can control output activity. An open-drain output
may be obtained by using the same signal for driving the
output and 3-state signal nets so that the buffer output is
enabled only for a Low.
Configuration program bits for each IOB control features
such as optional output register, logic signal inversion, and
3-state and slew-rate control of the output.
The program-controlled memory cells of Figure 4 control
the following options.
Logic inversion of the output is controlled by one
configuration program bit per IOB.
Logic 3-state control of each IOB output buffer is
determined by the states of configuration program bits
that turn the buffer on, or off, or select the output buffer
3-state control interconnection (IOB pin T). When this
IOB output control signal is High, a logic one, the buffer
is disabled and the package pin is high impedance.
When this IOB output control signal is Low, a logic zero,
the buffer is enabled and the package pin is active.
Inversion of the buffer 3-state control-logic sense
(output enable) is controlled by an additional
configuration program bit.
Direct or registered output is selectable for each IOB.
The register uses a positive-edge, clocked flip-flop. The
clock source may be supplied (IOB pin OK) by either of
two metal lines available along each die edge. Each of
these lines is driven by an invertible buffer.
Increased output transition speed can be selected to
improve critical timing. Slower transitions reduce
capacitive-load peak currents of non-critical outputs
and minimize system noise.
An internal high-impedance pull-up resistor (active by
default) prevents unconnected inputs from floating.
Unlike
the
original
XC3000
series,
the
XC3000A,
XC3000L, XC3100A, and XC3100L families include the
Soft Startup feature. When the configuration process is fin-
ished and the device starts up in user mode, the first activa-
tion of the outputs is automatically slew-rate limited. This
feature avoids potential ground bounce when all outputs
are turned on simultaneously. After start-up, the slew rate
of the individual outputs is determined by the individual
configuration option.
Summary of I/O Options
Inputs
-Direct
-
Flip-flop/latch
-
CMOS/TTL threshold (chip inputs)
-
Pull-up resistor/open circuit
Outputs
-
Direct/registered
-
Inverted/not
-
3-state/on/off
-
Full speed/slew limited
-
3-state/output enable (inverse)
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| RCB108DHBR | CONN EDGECARD 216PS R/A .050 DIP |
| XC3120A-3PC68C | IC LOGIC CL ARRAY 2000GAT 68PLCC |
| ASC49DRYN-S93 | CONN EDGECARD 98POS DIP .100 SLD |
| XC3090A-7PC84C | IC LOGIC CL ARRAY 9000GAT 84PLCC |
| XC3064A-7PC84C | IC LOGIC CL ARRAY 6400GAT 84PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC3130A-3PC84I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays (XC3000A/L, XC3100A/L) |
| XC3130A-3PQ100C | 功能描述:IC LOGIC CL ARRAY 3000GAT 100PQF RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC3000A/L 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55） |
| XC3130A-3PQ100C0262 | 制造商:Xilinx 功能描述: |
| XC3130A-3PQ100I | 制造商:Xilinx 功能描述: |
| XC3130A-3VQ100C | 制造商:Xilinx 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。