參數資料
型號： XC2S30-5CS144C
廠商： Xilinx Inc
文件頁數： 78/99頁
文件大?。?/td> 0K
描述： IC FPGA 2.5V C-TEMP 144-CSBGA
標準包裝： 198
系列： Spartan®-II
LAB/CLB數： 216
邏輯元件/單元數： 972
RAM 位總計： 24576
輸入/輸出數： 92
門數： 30000
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 144-TFBGA，CSPBGA
供應商設備封裝： 144-LCSBGA（12x12）
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
8
R
The three IOB registers function either as edge-triggered
D-type flip-flops or as level-sensitive latches. Each IOB has
a clock signal (CLK) shared by the three registers and
independent Clock Enable (CE) signals for each register. In
addition to the CLK and CE control signals, the three
registers share a Set/Reset (SR). For each register, this
signal can be independently configured as a synchronous
Set, a synchronous Reset, an asynchronous Preset, or an
asynchronous Clear.
A feature not shown in the block diagram, but controlled by
the software, is polarity control. The input and output buffers
and all of the IOB control signals have independent polarity
controls.
Optional pull-up and pull-down resistors and an optional
weak-keeper circuit are attached to each pad. Prior to
configuration all outputs not involved in configuration are
forced into their high-impedance state. The pull-down
resistors and the weak-keeper circuits are inactive, but
inputs may optionally be pulled up.
The activation of pull-up resistors prior to configuration is
controlled on a global basis by the configuration mode pins.
If the pull-up resistors are not activated, all the pins will float.
Consequently, external pull-up or pull-down resistors must
be provided on pins required to be at a well-defined logic
level prior to configuration.
All pads are protected against damage from electrostatic
discharge (ESD) and from over-voltage transients. Two
forms of over-voltage protection are provided, one that
permits 5V compliance, and one that does not. For 5V
compliance, a zener-like structure connected to ground
turns on when the output rises to approximately 6.5V. When
5V compliance is not required, a conventional clamp diode
may be connected to the output supply voltage, VCCO. The
type of over-voltage protection can be selected
independently for each pad.
All Spartan-II FPGA IOBs support IEEE 1149.1-compatible
boundary scan testing.
Input Path
A buffer In the Spartan-II FPGA IOB input path routes the
input signal either directly to internal logic or through an
optional input flip-flop.
An optional delay element at the D-input of this flip-flop
eliminates pad-to-pad hold time. The delay is matched to
the internal clock-distribution delay of the FPGA, and when
used, assures that the pad-to-pad hold time is zero.
Each input buffer can be configured to conform to any of the
low-voltage signaling standards supported. In some of
these standards the input buffer utilizes a user-supplied
threshold voltage, VREF. The need to supply VREF imposes
constraints on which standards can used in close proximity
to each other. See "I/O Banking," page 9.
There are optional pull-up and pull-down resistors at each
input for use after configuration.
Output Path
The output path includes a 3-state output buffer that drives
the output signal onto the pad. The output signal can be
routed to the buffer directly from the internal logic or through
an optional IOB output flip-flop.
The 3-state control of the output can also be routed directly
from the internal logic or through a flip-flip that provides
synchronous enable and disable.
Each output driver can be individually programmed for a
wide range of low-voltage signaling standards. Each output
buffer can source up to 24 mA and sink up to 48 mA. Drive
strength and slew rate controls minimize bus transients.
In most signaling standards, the output high voltage
depends on an externally supplied VCCO voltage. The need
to supply VCCO imposes constraints on which standards
can be used in close proximity to each other. See "I/O
An optional weak-keeper circuit is connected to each
output. When selected, the circuit monitors the voltage on
the pad and weakly drives the pin High or Low to match the
input signal. If the pin is connected to a multiple-source
signal, the weak keeper holds the signal in its last state if all
Table 3: Standards Supported by I/O (Typical Values)
I/O Standard
Input
Reference
Voltage
(VREF)
Output
Source
Voltage
(VCCO)
Board
Termination
Voltage
(VTT)
LVTTL (2-24 mA)
N/A
3.3
N/A
LVCMOS2
N/A
2.5
N/A
PCI (3V/5V,
33 MHz/66 MHz)
N/A
3.3
N/A
GTL
0.8
N/A
1.2
GTL+
1.0
N/A
1.5
HSTL Class I
0.75
1.5
0.75
HSTL Class III
0.9
1.5
HSTL Class IV
0.9
1.5
SSTL3 Class I
and II
1.5
3.3
1.5
SSTL2 Class I
and II
1.25
2.5
1.25
CTT
1.5
3.3
1.5
AGP-2X
1.32
3.3
N/A
相關PDF資料
PDF描述
24LC024H-E/ST IC EEPROM 2KBIT 400KHZ 8TSSOP
748333-7 CONN D-SUB PIN 22-28AWG AU
ACM43DTAT-S189 CONN EDGECARD 86POS R/A .156 SLD
XC3S200A-4VQG100C IC FPGA SPARTAN-3A 200K 100-VQFP
24LC08BHT-E/ST IC EEPROM 8KBIT 400KHZ 8TSSOP
相關代理商/技術參數
參數描述
XC2S30-5CS144I 功能描述:IC FPGA 2.5V I-TEMP 144-CSBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA（27x27）
XC2S30-5CSG144C 制造商:Xilinx 功能描述:FPGA SPARTAN-II 30K GATES 972 CELLS 263MHZ 2.5V 144CSBGA - Trays 制造商:Xilinx 功能描述:IC SYSTEM GATE
XC2S30-5CSG144I 制造商:Xilinx 功能描述:IC SYSTEM GATE 制造商:Xilinx 功能描述:FPGA SPARTAN-II 30K GATES 972 CELLS 263MHZ 2.5V 144CSBGA - Trays
XC2S30-5FG256C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information
XC2S30-5FG256I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*