- 您現在的位置：買賣IC網 > PDF目錄372541 > X9C503PZ (INTERSIL CORP) Digitally Controlled Pot (XDCP) PDF資料下載
參數資料
| 型號： | X9C503PZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Digitally Controlled Pot (XDCP) |
| 中文描述： | 50K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 100 POSITIONS, PDIP8 |
| 封裝： | ROHS COMPLIANT, PLASTIC, DIP-8 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 257K |
| 代理商： | X9C503PZ |
8
FN8222.1
September 19, 2005
INSTRUCTIONS AND PROGRAMMING
The INC, U/D and CS inputs control the movement of
the wiper along the resistor array. With CS set LOW
the device is selected and enabled to respond to the
U/D and INC inputs. HIGH to LOW transitions on INC
will increment or decrement (depending on the state of
the U/D input) a seven-bit counter. The output of this
counter is decoded to select one of one-hundred wiper
positions along the resistive array.
The value of the counter is stored in nonvolatile mem-
ory whenever CS transitions HIGH while the INC input
is also HIGH.
The system may select the X9Cxxx, move the wiper,
and deselect the device without having to store the lat-
est wiper position in nonvolatile memory. After the
wiper movement is performed as described above and
once the new position is reached, the system must
keep INC LOW while taking CS HIGH. The new wiper
position will be maintained until changed by the sys-
tem or until a power-down/up cycle recalled the previ-
ously stored data.
This procedure allows the system to always power-up
to a preset value stored in nonvolatile memory; then
during system operation minor adjustments could be
made. The adjustments might be based on user pref-
erence: system parameter changes due to tempera-
ture drift, etc...
The state of U/D may be changed while CS remains
LOW. This allows the host system to enable the
device and then move the wiper up and down until the
proper trim is attained.
MODE SELECTION
SYMBOL TABLE
CS
INC
U/D
Mode
L
H
Wiper Up
L
L
Wiper Down
H
X
Store Wiper Position
H
X
X
Standby Current
L
X
No Store, Return to Standby
L
H
Wiper Up (not recommended)
L
L
Wiper Down (not recommended)
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
May change
from High to
Low
Will change
from Low to
High
Will change
from High to
Low
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
X9C102, X9C103, X9C104, X9C503
相關PDF資料 |
PDF描述 |
|---|---|
| X9C503S | Digitally Controlled Pot (XDCP) |
| X9C503SI | Digitally Controlled Pot (XDCP) |
| X9C103SZ | Digitally Controlled Pot (XDCP) |
| X9C104P | Digitally Controlled Pot (XDCP) |
| X9C104P-3 | Digitally Controlled Pot (XDCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9C503S | 功能描述:IC DIGITAL POT 50K 100TP 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9C503SI | 功能描述:IC DIGITAL POT 50K 100TP 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9C503SIC7884 | 制造商:Intersil Corporation 功能描述: |
| X9C503SIC7928 | 制造商:Intersil Corporation 功能描述: |
| X9C503SIT1 | 功能描述:IC XDCP 100-TAP 50K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
發(fā)布緊急采購，3分鐘左右您將得到回復。