- 您現(xiàn)在的位置：買賣IC網 > PDF目錄376449 > X9522V20I-B (INTERSIL CORP) Laser Diode Control for Fiber Optic Modules PDF資料下載
參數資料
| 型號： | X9522V20I-B |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Laser Diode Control for Fiber Optic Modules |
| 中文描述： | DIGITAL POTENTIOMETER, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 9/29頁 |
| 文件大?。?/td> | 486K |
| 代理商： | X9522V20I-B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
9
FN8208.0
March 10, 2005
It should be noted that all writes to any DCP of the X9522
are random in nature. Therefore, the Data Byte of con-
secutive write operations to any DCP can differ by an
arbitrary number of bits. Also, setting the bits P1=1, P0=1
is a reserved sequence, and will result in no ACKNOWL-
EDGE after sending an Instruction Byte on SDA.
The factory default setting of all “wiper position” settings
is with 00h stored in the NVM of the DCPs. This corre-
sponds to having the “wiper teminal”
R
WX
(x = 0,1,2) at
the “l(fā)owest” tap position, Therefore, the resistance
between
R
WX
and
R
LX
is a minimum (essentially only the
Wiper Resistance,
R
W
).
DCP Read Operation
A read of DCPx (x = 0,1,2) can be performed using the
three byte random read command sequence shown in
Figure 10.
The master issues the START condition and the Slave
Address Byte 10101110 which specifies that a “dummy”
write” is to be conducted. This “dummy” write operation
sets which DCP is to be read (in the preceding Read
operation). An ACKNOWLEDGE is returned by the
X9522 after the Slave Address if received correctly. Next,
an Instruction Byte is issued on SDA. Bits P1-P0 of the
Instruction Byte determine which DCP “wiper position” is
to be read. In this case, the state of the WT bit is “don’t
care”. If the Instruction Byte format is valid, then another
ACKNOWLEDGE is returned by the X9522.
Following this ACKNOWLEDGE, the master immediately
issues another START condition and a valid Slave
address byte with the R/W bit set to 1. Then the X9522
issues an ACKNOWLEDGE followed by Data Byte, and
finally, the master issues a STOP condition. The Data
Byte read in this operation, corresponds to the “wiper
position” (value of the WCR) of the DCP pointed to by
bits P1 and P0.
It should be noted that when reading out the data byte
for DCP0 (64 Tap), the upper two most significant bits
are “unknown” bits. For DCP1 (100 Tap), the upper
most significant bit is an “unknown”. For DCP2 (256
Tap) however, all bits of the data byte are relevant (See
Figure 10).
CONTROL AND STATUS REGISTER
The Control and Status (CONSTAT) Register pro-
vides the user with a mechanism for changing and
reading the status of various parameters of the
X9522 (See Figure 11).
The CONSTAT register is a combination of both volatile
and nonvolatile bits. The nonvolatile bits of the CON-
STAT register retain their stored values even when Vcc /
V1 is powered down, then powered back up. The volatile
bits however, will always power-up to a known logic state
“0” (irrespective of their value at power-down).
Slave
Address
Instruction
Byte
A
C
K
A
C
K
S
t
a
r
t
S
t
o
p
Slave
Address
Data Byte
A
C
K
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from
the Master
Figure 10. DCP Read Sequence
“Dummy” write
READ Operation
101 111
0
00 00
W
T
P
1
P
0
101 111
1
WRITE Operation
-
- -
MSB
LSB
DCPx
x = 0
x = 1
x = 2
“-” = DON’T CARE
X9522
相關PDF資料 |
PDF描述 |
|---|---|
| X9523V20I-A | Laser Diode Control for Fiber Optic Modules |
| X9523V20I-B | Laser Diode Control for Fiber Optic Modules |
| X9523 | Laser Diode Control for Fiber Optic Modules |
| X9523B20I-A | RECTIFIER FAST-RECOVERY SINGLE 3A 50V 125A-ifsm 0.95V-vf 35ns 5uA-ir DO-201AD 1.2K/REEL-13 |
| X9523B20I-B | RECTIFIER FAST-RECOVERY SINGLE 3A 100V 125A-ifsm 0.95V-vf 35ns 5uA-ir DO-201AD 500/BULK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9522V20I-BT1 | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9522V20IZ-A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, Dual Voltage Monitors |
| X9522V20IZ-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, Dual Voltage Monitors |
| X9523 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules |
| X9523_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules |
發(fā)布緊急采購，3分鐘左右您將得到回復。