參數資料
型號： X9522
廠商： Intersil Corporation
英文描述： Laser Diode Control for Fiber Optic Modules
中文描述： 激光二極管控制光纖模塊
文件頁數： 11/29頁
文件大小： 486K
代理商： X9522
11
FN8208.0
March 10, 2005
CONSTAT Register Write Operation
The CONSTAT register is accessed using the Slave
Address set to 1010010 (Refer to Figure 4.). Following
the Slave Address Byte, access to the CONSTAT regis-
ter requires an Address Byte which must be set to FFh.
Only one data byte is allowed to be written for each
CONSTAT register Write operation. The user must issue
a STOP, after sending this byte to the register, to initiate
the nonvolatile cycle that stores the DWLK bit. The
X9522 will not ACKNOWLEDGE any data bytes written
after the first byte is entered (Refer to Figure 12.).
When writing to the CONSTAT register, the bits CS7,
CS4 and CS0 must all be set to “0”. Writing any other bit
sequence to bits CS7, CS4 and CS0 of the CONSTAT
register is reserved.
Prior to writing to the CONSTAT register, the WEL and
RWEL bits must be set using a two step process, with
the whole sequence requiring 3 steps:
—Write a 02H to the CONSTAT Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation preceded
by a START and ended with a STOP).
—Write a 06H to the CONSTAT Register to set the
Register Write Enable Latch (RWEL) AND the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation preceded by a START
and ended with a STOP).
—Write a one byte value to the CONSTAT Register that
has all the bits set to the desired state. The CONSTAT
register can be represented as 0xy0t010 in binary,
where xy are the Voltage Monitor Output Status
(V2OS and V3OS) bits, and t is the DCP Write Lock
(DWLK) bit. This operation is proceeded by a START
and ended with a STOP bit. Since this is a nonvolatile
write cycle, it will typically take 5ms to complete. The
RWEL bit is reset by this cycle and the sequence must
be repeated to change the nonvolatile bits again. If bit
2 is set to ‘1’ in this third step (0xy0 t110) then the
RWEL bit is set, but the DWLK bit will remain
unchanged. Writing a second byte to the control regis-
ter is not allowed. Doing so aborts the write operation
and the X9522 does not return an ACKNOWLEDGE.
For example, a sequence of writes to the device CON-
STAT register consisting of [02H, 06H, 02H] will reset the
nonvolatile (DWLK) bit in the CONSTAT Register to “0”.
S
T
A
R
T
1
0
1
0
0
1
0
R/W A
C
K
1
1
1
1
1
1
1
1
A
C
K
SCL
SDA
S
T
O
P
A
C
K
CS7 CS6CS5 CS4 CS3 CS2CS1 CS0
SLAVE ADDRESS BYTE
ADDRESS BYTE
CONSTAT REGISTER DATA IN
Figure 12. CONSTAT Register Write Command Sequence
0
Slave
Address
Address
Byte
A
C
K
A
C
K
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
1
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from
the Master
Figure 13. CONSTAT Register Read Command Sequence
0 1 0 0 1 0
1
1
0 1 0 0 1 0
WRITE Operation
“Dummy” Write
READ Operation
CS7 … CS0
X9522
相關PDF資料
PDF描述
X9522B20I-A Laser Diode Control for Fiber Optic Modules
X9522B20I-B Laser Diode Control for Fiber Optic Modules
X9522V20I-A Laser Diode Control for Fiber Optic Modules
X9522V20I-B Laser Diode Control for Fiber Optic Modules
X9523V20I-A Laser Diode Control for Fiber Optic Modules
相關代理商/技術參數
參數描述
X9522_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, Dual Voltage Monitors
X9522B20I-A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules
X9522B20I-B 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules
X9522V20I-A 功能描述:IC TRIPL DCP LASER CNTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9522V20I-AT1 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*