參數資料
型號: X9430WS24M
英文描述: Interface IC
中文描述: 接口IC
文件頁數: 4/21頁
文件大?。?/td> 881K
代理商: X9430WS24M
X9430
– Preliminary Information
Characteristics subject to change without notice.
4 of 21
REV 1.0 6/20/00
www.xicor.com
Potentiometer/Array Description
The X9430 is comprised of two resistor arrays and two
operational amplifiers. Each array contains 63 discrete
resistive segments that are connected in series. The
physical ends of each array are equivalent to the fixed
terminals of a mechanical potentiometer (R
H
and R
L
).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(R
W
) output. Within each individual array only one
switch may be turned on at a time. These switches are
controlled by a volatile wiper counter register (WCR).
The six bits of the WCR are decoded to select, and
enable, one of sixty-four switches.
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
data registers into the WCR. These data registers and
the WCR can be read and written by the host system.
Operational Amplifier
The voltage operational amplifiers are CMOS rail-to-rail
output general purpose amplifiers. They are designed
to operate from dual (±) power supplies. The amplifiers
may be configured like any standard amplifier. All pins
are externally available to allow connection with the
potentiometers or as stand alone amplifiers.
Detailed Block Diagram
(One of 2 Circuits)
V
OUT (0,1)
(DR0-DR3)
0,1
Control and
Memory
CS
SCK
SO
SI
A1
A0
V
H (0,1)
V
L (0,1)
WP
V
W (0,1)
V
N (0,1)
+
WCR
0,1
(DR0-DR3)
0,1
V
INV (0,1)
V
SS
V
CC
HOLD
WCR0
WCR1
Write in Process
The contents of the data registers are saved to nonvol-
atile memory when the CS pin goes from LOW to
HIGH after a complete write sequence is received by
the device. The progress of this internal write opera-
tion can be monitored by a write in process bit (WIP).
The WIP bit is read with a read status command.
INSTRUCTIONS AND PROGRAMMING
Identification (ID) Byte
The first byte sent to the X9430 from the host, follow-
ing a CS going HIGH to LOW, is called the identifica-
tion byte. The most significant four bits of the slave
address are a device type identifier, for the X9430 this
is fixed as 0101[B] (refer to Figure 1).
相關PDF資料
PDF描述
X9430WS24M2.7 Interface IC
X9430WV24M Interface IC
X9430WV24 Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier
X9430WV24-2.7 Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier
X9430WV24I Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier
相關代理商/技術參數
參數描述
X9430WS24M2.7 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC
X9430WV24 功能描述:IC DUAL DCP + OPAMP 10K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻(歐姆):100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP(3x3) 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT
X9430WV24-2.7 功能描述:IC DUAL DCP + OPAMP 10K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻(歐姆):100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP(3x3) 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT
X9430WV24I 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Digitally Controlled Potentiometer (XDCP⑩) with Operational Amplifier
X9430WV24I-2.7 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Digitally Controlled Potentiometer (XDCP⑩) with Operational Amplifier