參數資料
型號： X9428YS-2.7
廠商： INTERSIL CORP
元件分類： 數字電位計
英文描述： Single Digitally Controlled Potentiometer
中文描述： 2K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO16
封裝： 0.300 INCH, PLASTIC, SOIC-16
文件頁數： 3/20頁
文件大?。?/td> 580K
代理商： X9428YS-2.7
X9428
Characteristics subject to change without notice.
3 of 20
REV 1.1.5 7/8/03
www.xicor.com
PRINCIPLES OF OPERATION
The X9428 is a highly integrated microcircuit
incorporating a resistor array and its associated
registers and counters and the serial interface logic
providing direct communication between the host and
the XDCP potentiometers.
Serial Interface
The X9428 supports a bidirectional bus oriented
protocol. The protocol defines any device that sends
data onto the bus as a transmitter and the receiving
device as the receiver. The device controlling the
transfer is a master and the device being controlled is
the slave. The master will always initiate data transfers
and provide the clock for both transmit and receive
operations. Therefore, the X9428 will be considered a
slave device in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW periods (t
LOW
). SDA state changes during
SCL HIGH are reserved for indicating start and stop
conditions.
Start Condition
All commands to the X9428 are preceded by the start
condition, which is a HIGH to LOW transition of SDA
while SCL is HIGH (t
HIGH
). The X9428 continuously
monitors the SDA and SCL lines for the start condition
and will not respond to any command until this
condition is met.
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH.
Acknowledge
Acknowledge is a software convention used to provide
a positive handshake between the master and slave
devices on the bus to indicate the successful receipt of
data. The transmitting device, either the master or the
slave, will release the SDA bus after transmitting eight
bits. The master generates a ninth clock cycle and
during this period the receiver pulls the SDA line LOW
to acknowledge that it successfully received the eight
bits of data.
The X9428 will respond with an acknowledge after
recognition of a start condition and its slave address
and once again after successful receipt of the
command byte. If the command is followed by a data
byte the X9428 will respond with a final acknowledge.
Array Description
The X9428 is comprised of a resistor array. The array
contains 63 discrete resistive segments that are
connected in series. The physical ends of the array are
equivalent to the fixed terminals of a mechanical
potentiometer (V
H
/R
H
and V
L
/R
L
inputs).
At both ends of the array and between each resistor
segment is a CMOS switch connected to the wiper
(V
W
/R
W
) output. Within each individual array only one
switch may be turned on at a time. These switches are
controlled by the Wiper Counter Register (WCR). The
six bits of the WCR are decoded to select, and enable,
one of sixty-four switches.
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
Data Registers into the WCR. These Data Registers
and the WCR can be read and written by the host
system.
Device Addressing
Following a start condition the master must output the
address of the slave it is accessing. The most
significant four bits of the slave address are the device
type identifier (refer to Figure 1 below). For the X9428
this is fixed as 0101[B].
Figure 1. Slave Address
The next four bits of the slave address are the device
address. The physical device address is defined by the
state of the A
0
, A
2
, A
3
inputs. The X9428 compares the
serial data stream with the address input state; a
successful compare of all four address bits is required
for the X9428 to respond with an acknowledge. The A
A
2
, A
3
inputs can be actively driven by CMOS input
signals or tied to V
CC
or V
SS
0
,
.
1
0
0
A3
A2
0
A0
Device Type
Identifier
Device Address
1
相關PDF資料
PDF描述
X9428YP-2.7 CAT5E PATCH CORD 25 FOOT BEIGE
X9428WVI-2.7 Single Digitally Controlled Potentiometer
X9428WV-2.7 Single Digitally Controlled Potentiometer
X9428WSI-2.7 Single Digitally Controlled Potentiometer
X9428WPI-2.7 Single Digitally Controlled Potentiometer
相關代理商/技術參數
參數描述
X9428YSI 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled Potentiometer
X9428YSI-2.7 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled Potentiometer
X9428YSM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC
X9428YSM2.7 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC
X9428YV 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled Potentiometer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*