參數資料
型號： X9428WP
廠商： INTERSIL CORP
元件分類： 數字電位計
英文描述： 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDIP16
封裝： PLASTIC, DIP-16
文件頁數： 4/20頁
文件大?。?/td> 580K
代理商： X9428WP
X9428
Characteristics subject to change without notice.
12 of 20
REV 1.1.5 7/8/03
www.xicor.com
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used
as a potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potenti-
ometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (RH—RL)/63, single pot
(4) Max. = all four arrays cascaded together, Typical = individual array resolutions.
ENDURANCE AND DATA RETENTION
CAPACITANCE
POWER-UP TIMING
POWER-UP AND POWER-DOWN
There are no restrictions on the power-up or power-down sequencing of the bias supplies VCC, V+, and V- provided
that all three supplies reach their nal values within 1msec of each other. However, at all times, the voltages on the
potentiometer pins must be less than V+ and more than V–. The recall of the wiper position from nonvolatile
memory is not in effect until all supplies reach their nal value.
Notes: (5) This parameter is periodically sampled and not 100% tested
(6) tPUR and tPUW are the delays required from the time the third (last) power supply (VCC, V+ or V-) is stable until the specic
instruction can be issued. These parameters are periodically sampled and not 100% tested.
(7) Sample tested only.
Symbol
Parameter
Limits
Test Conditions
Min.
Typ.
Max.
Unit
ICC1
VCC supply current
(nonvolatile write)
1mA
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ICC2
VCC supply current
(move wiper, write, read)
100
A
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ISB
VCC current (standby)
1
A
SCL = SDA = VCC, Addr. = VSS
ILI
Input leakage current
10
A
VIN = VSS to VCC
ILO
Output leakage current
10
A
VOUT = VSS to VCC
VIH
Input HIGH voltage
VCC x 0.7
VCC x 0.5
V
VIL
Input LOW voltage
–0.5
VCC x 0.1
V
VOL
Output LOW voltage
0.4
V
IOL = 3mA
Parameter
Min.
Unit
Minimum endurance
100,000
Data changes per bit per register
Data retention
100
Years
Symbol
Test
Max.
Unit
Test Conditions
CI/O
(5)
Input/output capacitance (SDA)
8
pF
VI/O = 0V
CIN
(5)
Input capacitance (A0, A1, A2, A3, and SCL)
6
pF
VIN = 0V
Symbol
Parameter
Min.
Typ.
Max.
Unit
tPUR
(6)
Power-up to initiation of read operation
1
ms
tPUW
(6)
Power-up to initiation of write operation
5
ms
tRVCC
(7)
VCC Power up ramp rate
0.2
50
V/msec
相關PDF資料
PDF描述
X9438WP24I-2.7 DUAL DIGITAL POTENTIOMETER, PDIP24
X9650M Bandpass Filter
X9C103SM 10K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 100 POSITIONS, PDSO8
XAA170 DUAL POLE OptoMOS Relay
XAA170P DUAL POLE OptoMOS Relay
相關代理商/技術參數
參數描述
X9428WP16I-2.7 功能描述:IC XDCP SGL 64-TAP 10K 16-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
X9428WP-2.7 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Digitally Controlled Potentiometer
X9428WPI 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled Potentiometer
X9428WPI-2.7 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled Potentiometer
X9428WS 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled Potentiometer
發布緊急采購，3分鐘左右您將得到回復。