- 您現在的位置：買賣IC網 > PDF目錄371300 > X9421WS-2.7 Single Digitally Controlled (XDCP) Potentiometer PDF資料下載
參數資料
| 型號： | X9421WS-2.7 |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally Controlled (XDCP) Potentiometer |
| 中文描述： | 單數控（數字電位器）電位 |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 117K |
| 代理商： | X9421WS-2.7 |
X9421
REV 1.1.6 8/1/02
Characteristics subject to change without notice.
6 of 21
www.xicor.com
Write in Process
The contents of the Data Registers are saved to
nonvolatile memory when the CS pin goes from LOW
to HIGH after a complete write sequence is received by
the device. The progress of this internal write operation
can be monitored by a Write In Process bit (WIP). The
WIP bit is read with a Read Status command.
INSTRUCTIONS
Address/Identification (ID) Byte
The first byte sent to the X9421 from the host, following
a CS going HIGH to LOW, is called the Address or
Identification byte. The most significant four bits of the
slave address are a device type identifier, for the
X9421 this is fixed as 0101[B] (refer to Figure 2).
The least significant bit in the ID byte selects one of
two devices on the bus. The physical device address is
defined by the state of the A
0
input pin. The X9421
compares the serial data stream with the address input
state; a successful compare of the address bit is
required for the X9421 to successfully continue the
command sequence. The A
0
input can be actively
driven by a CMOS input signal or tied to V
CC
or V
SS
.
The remaining three bits in the ID byte must be set to
110.
Figure 2. Address/Identification Byte Format
Instruction Byte
The next byte sent to the X9421 contains the
instruction and register pointer information. The four
most significant bits are the instruction. The next two
bits point to one of four Data Registers. The format is
shown below in Figure 3.
Figure 3. Instruction Byte Format
1
0
0
1
1
0
A0
Device Type
Identifier
Device Address
1
I1
I2
I3
I0
R1
R0
0
0
Register
Select
Instructions
Figure 1. Detailed Potentiometer Block Diagram
Serial Data Path
From Interface
Circuitry
Register 0
Register 1
REGISTER 2
REGISTER 3
Serial
Bus
Input
Parallel
Bus
Input
Counter
Register
(WCR)
INC/DEC
Logic
UP/DN
CLK
Modified SCK
UP/DN
V
H
V
L
V
W
8
6
C
O
U
N
T
E
R
D
E
C
O
D
E
IF WCR = 00[H] THEN V
W
= V
L
IF WCR = 3F[H] THEN V
W
= V
H
Wiper
相關PDF資料 |
PDF描述 |
|---|---|
| X9421WSI | Single Digitally Controlled (XDCP) Potentiometer |
| X9421WVI | SWITCH |
| X9421WVI-2.7 | SWITCH |
| X9421WSI-2.7 | Single Digitally Controlled (XDCP) Potentiometer |
| X9421WV | Single Digitally Controlled (XDCP) Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9421WSI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9421WSI-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9421WV | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9421WV14 | 功能描述:IC DIGITAL POT 10K 64TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9421WV14-2.7 | 功能描述:IC DIGITAL POT 10K 64TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。