- 您現在的位置：買賣IC網 > PDF目錄371298 > X9420WP-2.7 Single Digitally Controlled (XDCP) Potentiometer PDF資料下載
參數資料
| 型號： | X9420WP-2.7 |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally Controlled (XDCP) Potentiometer |
| 中文描述： | 單數控（數字電位器）電位 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 113K |
| 代理商： | X9420WP-2.7 |
X9420
Characteristics subject to change without notice.
4 of 20
REV 1.1.6 7/30/02
www.xicor.com
Write in Process
The contents of the Data Registers are saved to
nonvolatile memory when the CS pin goes from LOW
to HIGH after a complete write sequence is received by
the device. The progress of this internal write operation
can be monitored by a Write In Process bit (WIP). The
WIP bit is read with a Read Status command.
INSTRUCTIONS
Address/Identification (ID) Byte
The first byte sent to the X9420 from the host, following
a CS going HIGH to LOW, is called the Address or
Identification byte. The most significant four bits of the
slave address are a device type identifier, for the
X9420 this is fixed as 0101[B] (refer to Figure 2).
The least significant bit in the ID byte selects one of
two devices on the bus. The physical device address is
defined by the state of the A
compares the serial data stream with the address input
state; a successful compare of the address bit is
required for the X9420 to successfully continue the
command sequence. The A
driven by a CMOS input signal or tied to V
0
input pin. The X9420
0
input can be actively
CC
or V
SS
.
The remaining three bits in the ID byte must be set to
110.
Figure 2. Address/Identification Byte Format
Instruction Byte
The next byte sent to the X9420 contains the
instruction and register pointer information. The four
most significant bits are the instruction. The next two
bits point to one of four data registers. The format is
shown below in Figure 3.
Figure 3. Instruction Byte Format
1
0
0
1
1
0
A0
Device Type
Identifier
Device Address
1
I1
I2
I3
I0
R1
R0
0
0
Register
Select
Instructions
Figure 1. Detailed Potentiometer Block Diagram
Serial Data Path
From Interface
Circuitry
Register 0
Register 1
REGISTER 2
REGISTER 3
Serial
Bus
Input
Parallel
Bus
Input
Counter
Register
(WCR)
INC/DEC
Logic
UP/DN
CLK
Modified SCK
UP/DN
V
H
V
L
V
W
8
6
C
O
U
N
T
E
R
D
E
C
O
D
E
IF WCR = 00[H] THEN V
W
= V
L
IF WCR = 3F[H] THEN V
W
= V
H
Wiper
相關PDF資料 |
PDF描述 |
|---|---|
| X9420WPI | Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPI-2.7 | Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPM | Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPM-2.7 | Single Digitally Controlled (XDCP) Potentiometer |
| X9420WS | Single Digitally Controlled (XDCP) Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9420WPI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPI-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPM-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WS | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。