- 您現在的位置：買賣IC網 > PDF目錄371298 > X9418 (Intersil Corporation) HEAT SINK, T-SLOT, 0.55K/W; Thermal resistance:0.55(degree C)/W; Width, external:125mm; Depth, external:120mm; Length / Height, external:135mm; Material:Aluminium; Surface finish:Bare Aluminium RoHS Compliant: NA PDF資料下載
參數資料
| 型號： | X9418 |
| 廠商： | Intersil Corporation |
| 英文描述： | HEAT SINK, T-SLOT, 0.55K/W; Thermal resistance:0.55(degree C)/W; Width, external:125mm; Depth, external:120mm; Length / Height, external:135mm; Material:Aluminium; Surface finish:Bare Aluminium RoHS Compliant: NA |
| 中文描述： | 雙數控電位器 |
| 文件頁數： | 3/21頁 |
| 文件大?。?/td> | 386K |
| 代理商： | X9418 |
X9418
Characteristics subject to change without notice.
3 of 21
REV 1.1.5 7/23/02
www.xicor.com
PRINCIPLES OF OPERATION
The X9418 is a highly integrated microcircuit
incorporating two resistor arrays and their associated
registers and counters and the serial interface logic
providing direct communication between the host and
the XDCP potentiometers.
Serial Interface
The X9418 supports a bidirectional bus oriented
protocol. The protocol defines any device that sends
data onto the bus as a transmitter and the receiving
device as the receiver. The device controlling the
transfer is a master and the device being controlled is
the slave. The master will always initiate data transfers
and provide the clock for both transmit and receive
operations. Therefore, the X9418 will be considered a
slave device in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW periods (t
LOW
). SDA state changes during
SCL HIGH are reserved for indicating start and stop
conditions.
Start Condition
All commands to the X9418 are preceded by the start
condition, which is a HIGH to LOW transition of SDA
while SCL is HIGH (t
HIGH
). The X9418 continuously
monitors the SDA and SCL lines for the start condition
and will not respond to any command until this
condition is met.
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH.
Acknowledge
Acknowledge is a software convention used to provide
a positive handshake between the master and slave
devices on the bus to indicate the successful receipt of
data. The transmitting device, either the master or the
slave, will release the SDA bus after transmitting eight
bits. The master generates a ninth clock cycle and
during this period the receiver pulls the SDA line LOW
to acknowledge that it successfully received the eight
bits of data.
The X9418 will respond with an acknowledge after
recognition of a start condition and its slave address
and once again after successful receipt of the
command byte. If the command is followed by a data
byte the X9418 will respond with a final acknowledge.
Array Description
The X9418 is comprised of two resistor arrays. Each
array contains 63 discrete resistive segments that are
connected in series. The physical ends of each array
are equivalent to the fixed terminals of a mechanical
potentiometer (V
H
/R
H
and V
L
/R
L
inputs).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(V
W
/R
W
) output. Within each individual array only one
switch may be turned on at a time. These switches are
controlled by the Wiper Counter Register (WCR). The
six bits of the WCR are decoded to select, and enable,
one of sixty-four switches.
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
Data Registers into the WCR. These Data Registers
and the WCR can be read and written by the host
system.
Device Addressing
Following a start condition the master must output the
address of the slave it is accessing. The most
significant four bits of the slave address are the device
type identifier (refer to Figure 1 below). For the X9418
this is fixed as 0101[B].
Figure 1. Slave Address
The next four bits of the slave address are the device
address. The physical device address is defined by the
state of the A
0
–A
3
inputs. The X9418 compares the
serial data stream with the address input state; a
successful compare of all four address bits is required
for the X9418 to respond with an acknowledge. The
A
0
–A
3
inputs can be actively driven by CMOS input
signals or tied to V
CC
or V
SS
.
1
0
0
A3
A2
A1
A0
Device Type
Identifier
Device Address
1
相關PDF資料 |
PDF描述 |
|---|---|
| X9418YS24I-2.7 | Dual Digitally Controlled Potentiometers |
| X9418YV24-2.7 | Hook-Up Wire; Conductor Size AWG:24; No. Strands x Strand Size:19 x 36; Jacket Color:Orange; Approval Bodies:UL; Approval Categories:UL AWM Style 1180; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/5 Type EE RoHS Compliant: Yes |
| X9418WP24 | SHIELDED NULL MODEM CBL DB25 MALE - DB25 MALE |
| X9418WP24-2.7 | SHIELDED NULL MODEM CBL DB25 MALE - DB25 MALE |
| X9418WP24I | SHIELDED NULL MODEM CBL DB25 MALE - DB25 FEMALE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9418_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers |
| X9418-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers |
| X9418WP24 | 功能描述:IC XDCP DUAL 64-TAP 10K 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9418WP24-2.7 | 功能描述:IC XDCP DUAL 64-TAP 10K 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9418WP24I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers |
發布緊急采購，3分鐘左右您將得到回復。