參數資料
型號: X9401YS24I
廠商: INTERSIL CORP
元件分類: 數字電位計
英文描述: QUAD 2.5K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24
封裝: PLASTIC, SOIC-24
文件頁數: 15/20頁
文件大?。?/td> 360K
代理商: X9401YS24I
4
FN8190.1
March 31, 2005
Detailed Potentiometer Block Diagram
Write in Process
The contents of the Data Registers are saved to non-
volatile memory when the CS pin goes from LOW to
HIGH after a complete write sequence is received by
the device. The progress of this internal write opera-
tion can be monitored by a Write In Process bit (WIP).
The WIP bit is read with a Read Status command.
INSTRUCTIONS
Identification (ID) Byte
The first byte sent to the X9401 from the host, follow-
ing a CS going HIGH to LOW, is called the Identifica-
tion byte. The most significant four bits of the slave
address are a device type identifier, for the X9401 this
is fixed as 0101[B] (refer to Figure 1).
The two least significant bits in the ID byte select one
of four devices on the bus. The physical device
address is defined by the state of the A0 - A1 input
pins. The X9401 compares the serial data stream with
the address input state; a successful compare of both
address bits is required for the X9401 to successfully
continue the command sequence. The A0 - A1 inputs
can be actively driven by CMOS input signals or tied to
VCC or VSS.
The remaining two bits in the slave byte must be set to 0.
Figure 1. Identification Byte Format
Instruction Byte
The next byte sent to the X9401 contains the instruc-
tion and register pointer information. The four most
significant bits are the instruction. The next four bits
point to one of the four pots and, when applicable, they
point to one of four associated registers. The format is
shown below in Figure 2.
Serial Data Path
From Interface
Circuitry
Register 0
Register 1
Register 2
Register 3
Serial
Bus
Input
Parallel
Bus
Input
Wiper
Counter
Register
INC/DEC
Logic
UP/DN
CLK
Modified SCL
UP/DN
VH/RH
VL/RL
VW/RW
If WCR = 00[H] then VW/RW = VL/RL
If WCR = 3F[H] then VW/RW = VH/RH
8
6
C
o
u
n
t
e
r
D
e
c
o
d
e
(WCR)
(One of Four Arrays)
1
00
0
A1
A0
Device Type
Identifier
Device Address
1
X9401
相關PDF資料
PDF描述
X9408WS24Z QUAD 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24
X9408YB24I-2.7 QUAD 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, BGA24
X9409YV24I QUAD 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24
X9417WS24I DUAL 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24
X9417WS24 DUAL 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24
相關代理商/技術參數
參數描述
X9401YS24I-2.7 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
X9401YV24I-2.7 功能描述:IC XDCP QUAD 64-TAP 2.5K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
X9408 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled (XDCP?) Potentiometers
X9408_09 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled (XDCP?) Potentiometers
X9408-2.7 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise/Low Power/2-Wire Bus